Shënim 1
Përzgjedhja e një unazë rregullimi kryhet vetëm në zëvendësimin e njërit nga detajet e mëposhtme: lidhësit e karikimit ose një transmetim, rasti i diferencialit ose kushinetat e një diferenciali.
Shënim 2
Preload e kushinetave diferenciale duhet të jetë 0.15-0.35 mm. Para tensionit sigurohet përzgjedhja e trashësisë së unazës së rregullimit nga ato të furnizuara si pjesë këmbimi. Unaza e rregullimit është instaluar në strehimin e strehimit të kutisë së shpejtësisë nën unazën e jashtme të mbajtësit diferencial.
1. Futni unazën e montimit prej 1.25 mm në strehëzën e mbajtësit të ingranazhit nën mbajtjen e diferencialit.
4. Vendosja e diferencimit në transmetimet e kartave.
5. Instaloni copë litari.
6. Krijimi i lidhjeve të kartelave në transmetuesit e kartelave.
7. Mbërtheni tre baraslargues nga njëra-tjetra arrë e fiksimit të karosës me moment 25,0 N · m (2,5 kg · m).
8. Kthejeni diferencën për vetë-përafrimin e kushinetave me disa rrotulla.
9. Vendosni një pllakë bazë me diametër të përshtatshëm në fund të fllanës diferenciale nga ana e strehimit të tufës.
10. Vendosni treguesin në stendë. Këmba treguese është montuar në pllakën mbështetëse me një preload prej 1 mm.
11. Me forcën nga poshtë, rrëshqitni diferencialin deri sa të shkojë, pa kthyer diferencën rreth boshtit.
12. Matni sasinë e lëvizjes aksiale të diferencialit duke hequr treguesin e treguesit. Llogaritni trashësinë e kërkuar të unazës së rregullimit për kushinetat diferenciale sipas formulës:
T = S C Y, ku:
T - trashësia e kërkuar e unazës së rregullimit, mm;
S - vlera e matur e zhvendosjes aksiale të diferencialit, mm;
C - vlera e preloadit të kushinetave diferenciale, e barabartë me 0.25 mm;
Y - trashësia e unazës së rregullimit, e barabartë me 1.25 mm.
Zgjidhni një unazë rregullimi të furnizuar si pjesë këmbimi për trashësinë e llogaritur T ± 0.1 mm.
Llogaritja e shembullit:
Vlera e çarjes axial S sipas treguesit është 0.95 mm. Ne e zëvendësojmë këtë vlerë në formulë, si dhe vlerën e preload të kushinetave C = 0.25 mm dhe trashësia e unazës rregulluese Y = 1.25 mm:
T = 0,95 0,25 1,25 = 2,45 mm.
Kështu, trashësia e unazës së rregullimit duhet të jetë 2.45 ± 0.1 mm.
13. Instalimi unazë të zgjedhur rregulluese në fole të kutisë veshje dhe shtypin në unazën e jashtme e mbajtjes së diferencial. Pastaj montoni kutinë e marsheve në rendin e përcaktuar në nënseksionin.
14. Pas bolting strehimin tufë gearbox dhe check - diferenciale duhet të rrotullohen lirisht dhe nuk kanë të luajë axial.
Për të kontrolluar kushtet teknike të pjesëve të këmbyesve të shpejtësisë, pastroni tërësisht dhe shpëlarje ato me vajgur ose me frymën e bardhë.
Në mbajtësen e folesë dhe në kapakun e kutisë së transmetimit nuk duhet të ketë të çara ose gropa. Dëmtimi i sipërfaqeve të vulave të manovrave dhe mbulimit mund të shkaktojë shtrembërim të boshteve dhe rrjedhjeve të naftës. Sipërfaqet crankcase, dhe kushineta për shufra nuk duhet të dëmtohen (chipped, të anketuarve dhe të ngjashme. D.) dhe veshur. Pjesë ndërprerë e boshte, boshte splined dhe sipërfaqet për dëmtim të ingranazhet dhe kushineta nuk janë të lejuara. Në sipërfaqet e uljes së ingranazheve nuk duhet të ketë shenja të shënjimit dhe veshin. Nuk lejohet ndarja dhe veshin e tepruar e dhëmbëve të ingranazhit. Kushinetat e topit dhe të rrotullit nuk duhet të dëmtohen në treadmills, separators, balls and rollers, si dhe çara dhe patate të skuqura në unazat. Rrotullimi i unazave mbajtëse duhet të jetë i qetë, pa penguar. Kushinetat e dëmtuara zëvendësohen me të reja. Mos deformoni shufrat dhe prizat e ingranazheve. Sipërfaqet e punës së forksave që vijnë në kontakt me groove të mëngëve rrëshqitës të sinkronizatorëve nuk duhet të kenë konsumim të tepruar. Rrjedhat në vrimat e kafazeve duhet të lëvizin lirshëm, pa penguar. Ne e montojmë kutinë e marsheve në mënyrë të kundërt.
Kur mbledhim diferencën, ne lubrifikojmë vaj gear satellites dhe ingranazhet e disqet.
Bearings montuar preload diferencial Preload kusht trashësinë e përzgjedhjes rregullimi unazë të montuar në strehim fole gearbox nga mban unazën e jashtme diferencial.
Diagrami i zgjedhjes së unazës së rregullimit për kushineta diferenciale:
1 - tregues;
2 - mandrinë;
3 - sjellja e diferencialit;
4 - strehimi i tufës;
5 - transmetuesit e karrierës;
6 - mandrinë;
7 - unazë rregullimi
Përzgjedhja e unazës rregullimi trashësi është e nevojshme, në rast të zëvendësimit të një nga pikat e mëposhtme: strehim diferenciale, diferencial duke mbajtur mbajtëse friksion dhe gearbox.
Preload i kushinetave diferenciale duhet të jetë 0.25 mm.
Për të siguruar këtë ngushtësi, është e nevojshme të zgjidhni trashësinë e saktë të unazës së rregullimit.
Kur zgjedhni një unazë rregullimi, do t'ju duhet: një unazë në rritje 1.25 mm e trashë, një qëndrim me një matës dial, një mandrinë.
Ne vendosim një unazë rregullimi në një transmetues karikimi të folesë dhe shndërrojmë një unazë të jashtme të drejtimit të diferencialit me ndihmën e një mandrini të diametrit të përshtatshëm. Ngjashme, diferencial ngulitur duke unazën e jashtme në tufë strehim Set gearbox diferencial strehim, dhe pastaj friksion arrat strehim dhe contractible housings (në një sasi prej të paktën tre aranzhuar equidistantly).
Ne kthyem diferencën me disa kthesa, për vetë-përafrimin e kushinetave. Set mandrinë (në formën e një plug) në diferenciale fund dhe strehim tufë në banak me një tregues, në mënyrë që këmba pushoi kundër mandrinë dhe për të krijuar një preload në treguesin 1 mm.
Ne e lëvizim diferencimin dhe e lexojmë treguesin. Trashësia e unazës së rregullimit llogaritet me formulën: S = A + B + C;
ku
S - trashësia e unazës së rregullimit,
A është madhësia e zhvendosjes aksiale të diferencialit,
B - vlera e preload e kushineta diferenciale,
C - trashësia e unazës së rregullimit (1.25 mm).
Pas përcaktimit trashësinë e mbajtëse Thumbwheel Sever ndërrues dhe friksion, largimin diferencial duke unazë e jashtme është sprucuar nga ingranazh strehim dhe zëvendësuar unazë rritje në rregullimin zgjedhur. Në pjesët rezervë janë furnizuar unaza rregulluese me trashësi prej 1.65 mm deri në 2.65 mm, me një hap deri në 0.05 mm.
Pas instalimit të diferencialit në strehimin e tufës, është e nevojshme të ndreqni një nga ingranazhet e disqet e rrotave me një tufë (spin) në mënyrë që ata të mos lëvizin nga vendet kur janë mbledhur. Kur grumbulluar ndryshim dhe bosht përzgjedhës me bastun pivot përkohësisht degreased vrimë ndërprerë në varet dhe kaloni strehim, si dhe vida konik fiksim ato. Para vidhosjes, vendosim një fije ngjitëse në fijet e vidhave. Unazat e jashtme të kushinetave të rul të boshteve, gjëndrat e boshtit kryesor, disqet dhe rrjedhin e përzgjedhësit të ingranazhit janë të shtypur me mandrela ose me gjatësi të përshtatshme të tubave. Në skajet e punimit të kutive mbushëse aplikojmë një shtresë të hollë vaji gear.
Nëse vula rrota drives kanë pikë maslosgonnye, strehimit tufë (për të përzënë të drejtë) të vendosur lob drejtën e nivel, dhe strehim transmetimit (për makinë majtë) - këmishë bredh nivel. Shigjetat në trupat e gjëndrave duhet të përputhen me drejtimin e rrotullimit të disqeteve kur makina lëviz përpara. Kur montoni boshtin sekondar, lubrifikoni pjesët me vaj gear. Ne zëvendësojmë unazat e bllokimit të shpërndarësave sinkronizues me ato të reja. Shpërndarës sinkronizues, gara e brendshme e rrotullës, mbajtja e topit dhe rrotullimi i vozitjes makinë përfundimtare shtypni boshtin me mandrela ose gjatesite e përshtatshme të tubave. Pas grumbulluar bosht mesme të kontrolluar funksionimin e synchronizers, të cilat lëvizin synchronizers tufë dorë për pozicionin e marshin e duhur.
Shtypni unazën e brendshme të mbajtjes së rulit dhe mbajtjen e topit në boshtin kryesor. Para instalimit bosht angazhohet dhëmbët veshje e dy boshte në këtë pozicion, të vendosur shigjetat në të strehimit tufë para montimin e strehimit gearbox me banim tufë dhe kopertinën e pasme është aplikuar në perimetrin e avionëve rondelë e një shtresë e hollë e sealant.
Përmasat: 84 * 6 cm, D brendshme: 58 cm, peshë: 45 kg.
Ne bëjmë unaza shtesë të rregullimit me një lartësi prej 40 mm, 50 mm, 70 mm.
Ngritja e puseve të unazave të forta, përdorin gjerësisht produkte konkrete - unazat rregulluese shtesë. Unaza shtesë prodhohen dhe shiten me çmime të arsyeshme nga kompania "Art-Block". unaza rregullimi janë të dizajnuara për ngarkesë të përhershme dhe të përkohshme dhe janë bërë në teknologjitë moderne të materialeve të kualitetit të lartë, të përmbushë plotësisht kërkesat e dokumentacionit normative-teknike dhe lehtësinë e instalimit janë të ndryshme. Dorëzimi i produkteve në vendin e ndërtimit kryhet.
Rregullimi i unazës
Prodhim dhe kompani ndërtimi LLC "Art-Block" është e angazhuar në furnizimin komplekse e produkteve të betonit dhe materialeve të ndërtimit, produkteve të betonit, betonit të gatshëm, agregateve të materialeve pjesa më e madhe në vendet e ndërtimit dhe objekteve të Rusisë. Ne prodhojmë dhe prodhojmë struktura betoni për projekte individuale të klientit.
Në ndërtimin e unazave të mirë dhe dizenjot e tjera të puseve, si në rrugë private ashtu edhe në rrugë, përdoren disa elementë të mirë. Ai gjithashtu përfshin një shtesë shtesë (referuese) të rregullimit të quajtur KO-6. Unaza e rregullimit KO-6 është menduar për një pus me një lartësi më të ulët. Me ndihmën e DA-6 të unazës përshtatur në lente mund të jetë për të ndërtuar të njëjtën lartësi e ndërtimeve të unazave kapanxhë. KO-6 qëndron për markën e produktit si: KO - unazë mbështetëse; 6 - diametri i hapjes (të brendshme) të punës së gojës së pusit në decimetra. Ajo është e lejuar për të rritur dhe për të ulur rregullim lartësi e mbështetës unazës, në lidhje me këtë kompani "Art Block" prodhojnë bashkë-6 me një lartësi: 40; 50; 60; 70; 100 mm. Një unazë shtesë rregulluese shërben për të instaluar pusetat e gize në lartësinë e dëshiruar nga unazat e puseve për të siguruar koinçidencën dhe integritetin e nivelit të rrugës. Përdoret në mënyrë aktive kur instalon çelësa të hedhur në një nivel të ri të sipërfaqes së rrugës pas riparimit ose rindërtimit. K0-6 është bërë prej betoni të klasës së lartë dhe ka një kornizë metalike për forcë më të lartë.
Ne prodhojnë duke mbajtur përshtatur unaza dhe elemente të tjera të puseve në përputhje të plotë të të gjitha standardeve dhe normave të Enjoy 8020-90.
Në kompaninë "Art-Bllokut" Ju mund të blini e nevojshme për ju produkte të cilësisë së shkëlqyer me çmim të fabrikës dhe të ofrimit të rendit si një makinë bordit dhe si një manipulator.
Faqe 1
Unazat e rregullimit janë instaluar kur zhbllokojnë reducer, gaskets - pas heqjes së mbulesave. Pastrimi me kapakë të ngulitur kontrollohet me një matës të ndjeshmërisë.
Unazat e rregullimit vendosen (në uljen rrëshqitëse të klasës së 2) në një gjilpërë mulliri 5 midis dy hapëse montues. Unaza / është bashkuar më pas me një çelës 4 me një mandrinë, dhe unaza 3 mund të rrotullohet në një mandrinë. Unazat 1 dhe 3 janë ngjitur me njëri-tjetrin nga sipërfaqet e vidës fundore.
Në ndërtim a, unazat e rregullimit 1 bëhen të plota.
Në varësi të madhësisë të rregullimit fllanxhë unazë 30 vendoset midis rul 25, 26, 27, 28 ose 31 në një washers lëvizshëm ose njëkohësisht nga këto nyje.
IS-fut; 20 - levë; Unazat e rregullimit të hekurit 21; 22 - bosht i krahut karrige; D-sensor me kumbull poshtë (PES, SEW); P - duke treguar pajisjen (lloji E-280); Regjistruesi C (tipi E-610); M është motor i Warren.
Lexime të gabuara të pajisjes sekondare, pasi unazat e rregullimit rrëzohen.
Për të marrë gjerësinë e saktë të brazdës kur mulliri me mullinj disk, përdoren unazat e rregullimit.
Futur në vrimes strehim të në dalje, boshte ndërmjetme dhe hyrëse dhe të rregullimit kushineta unazë kapakun e rregulluar pastrimin aksiale në varg 4, 0 - 2 0 mm dhe të mbyllur kapak hapjes.
Kur montimi kushineta janë përdorur: burimin unazë ndarje për fiksimin unaza e jashtme e vinçave rul, rregullim unazë 6 janë instaluar midis unazat e jashtme të aftësi mbajtëse dhe fllanxha shtueshme dhe mëngë spacer midis unaza e brendshme të rul dhe Kushineta. Boshllëqet në mes të dhëmbëve është e rregulluar nga ndarësit çelikut 10 dhe 12 janë të instaluar në mes të shtëpive fllanxhë 15 dhe / dhe vendeve në bllok. Zhdoganimi ndërmjet unazave të jashtme të kushinetave të topit përcaktohet nga bluarja e unazave të rregullimit.
Në një lokomotivë 2 - 4 - 2, rrethoja e plotë mbështetet në djep përmes tre unazave të rregullimit.
Në lokomotivat 2 - 4 - 2 kyçi i uritur mbështetet në djep përmes tre unazave të rregullimit. E mesme është e pajisur me kanale për furnizimin e lubrifikantit me sipërfaqen mbështetëse. Në lokomotivat FD, FD, L, LV, CO, bashkimi kryhet përmes një shirit mbështetës të çelikut pranë thembra të mbështetëses. Në thembër, një kanal është shpuar, lubrifikant për të cilin është ushqyer përmes një valvul flutur.