Tehnologiile moderne pătrund din ce în ce mai adânc în cele mai diverse sectoare ale vieții umane. Și acum există posibilitatea de a diagnostica mașina în garaj, fără măcar să o dezasamblați. Acesta este disponibil dacă există o ieșire OBD2 pe vehicul și un autoscaner special din seria ELM. Cum se utilizează ELM327 va fi discutat în acest articol.
Mecanisme de autodiagnosticare
Producătorii de mașini încearcă să își proiecteze echipamentele astfel încât să poată scana rapid defecțiunile și, de asemenea, să le elimine rapid.
Pentru aceasta, a fost adoptat standardul de diagnostic OBD2, rezultat din mai multe etape de dezvoltare și testare îndelungată. Sarcina sa este de a monitoriza starea motorului, a părților individuale ale corpului și a rețelei de control intern. Producătorii pot utiliza diferite implementări de protocol pentru a conecta OBD la vehicul.
Standardul definește și conectorul prin care se pot obține informații de diagnostic. Este un sistem tip priză cu 16 contacte. De asemenea, specificația OBD presupune prezența unui conector în imediata apropiere a volanului.
Coduri de eroare OBD2
Mesajul de eroare de la sistem constă dintr-o literă și o secvență de 4 numere. Decriptarea lor arată astfel:
- scrisoare. Indică un subsistem cu probleme;
- a doua cifră. În cea mai mare parte, conține 0, dar poate fi 1 sau 2. Nu contează cu adevărat, deoarece este folosit la compilarea unui număr total pentru a clarifica o anumită defecțiune;
- a treia cifră indică tipul defecțiunii;
- ultimele două cifre sunt codul erorii în sine.
Simbolul literei poate avea mai multe semnificații, în funcție de clasa de echipament în care a fost găsită defecțiunea:
- B. Tot ce tine de caroserie. Perne, încuietori centralizate, geamuri electrice etc.;
- C. Tren de rulare;
- P. Motor sau transmisie;
- U. Sisteme electronice interne.
Tipul de rupere sau a treia cifră poate lua, de asemenea, mai multe valori standard:
- 1 sau 2. Sistem de alimentare cu combustibil;
- 3. Aprindere;
- 4. Control auxiliar;
- 5. Viraje în gol;
- 6. Circuite electronice interne;
- 7 sau 8. Transmisie.
Coduri de eroare OBD2 comune
- P0100. Senzor debit de aer defect.
- P0251. Indică faptul că există o problemă la pompa de injecție a turbinei.
- P0322. Nu există semnal de la distribuitorul de aprindere.
- P0340. Probleme cu senzorul arborelui cu came.
- P1603. Eroare EEPROM.
- S0276. Circuitul releului supapei este defect.
- B0835. Circuit de aprindere 1 defect.
- P1812. Supraîncălzirea transmisiei.
Numărul de coduri este de fapt foarte mare. Prin urmare, înainte de a utiliza ELM327, se recomandă să căutați pe Internet o listă completă a acestora. Este posibil ca multe dintre transcrieri să nu fie traduse în rusă. Ce poți face, caietul de sarcini este străin, trebuie să te aprofundezi și să stăpânești limba engleză.
ELM327 Auto Scanner Review
În funcție de producător, în exterior dispozitivul poate arăta ca o cutie mică cu un conector tată. Sarcina sa este de a citi date de la diverși senzori de motor, sisteme electronice, coduri de eroare și de a le reseta în memoria computerului.
Există mai multe opțiuni pentru a lucra cu ELM327. Acestea sunt Bluetooth, Wi-Fi și cablu USB.
Conectarea dispozitivului
După cum sa menționat mai devreme, ELM327 se conectează la portul OBD2 al vehiculului. Trebuie doar să-l introduci până la capăt și gata. Apoi, în funcție de tipul de comunicare cu dispozitivul, se efectuează diverse manipulări.
Cum să utilizați ELM327 cu Bluetooth
Acesta este probabil cel mai simplu și mai convenabil mod de a efectua autodiagnostica. Apoi, trebuie să vă conectați de pe telefon prin Bluetooth cu un scaner.
Acum vine alegerea software-ului. De fapt, există multe produse pe Internet care pot funcționa cu scanere. Să luăm în considerare cele mai cunoscute și utilizate în mod obișnuit înainte de a folosi ELM327 în domeniu.
Cuplu
Aplicație multifuncțională, în principiu, înlocuind computerul de bord. Se înțelege foarte bine cu conectivitatea Bluetooth. Funcționează rapid și nu junk. Există două versiuni disponibile în Google Play - Lite gratuit și Pro comercial.
Interfața este simplă, dar funcțională. Cum se utilizează ELM327 cu aplicația conectată? Foarte simplu. Este suficient să-l lansați, să specificați mai mulți parametri în profil și să selectați pictograma corespunzătoare, în funcție de situație.
Programul are următoarele caracteristici:
- citirea și ștergerea informațiilor despre erori din unitatea de control electronică a mașinii;
- autodiagnosticare;
- afișarea stării actuale a echipamentelor în diferite moduri grafice;
- capacitatea de a crea widget-uri pentru desktopul smartphone-ului.
Aceasta este o listă incompletă a caracteristicilor și caracteristicilor aplicației, așa că este recomandabil să citiți instrucțiunile de utilizare a acesteia înainte de a utiliza ELM327 Bluetooth în Android.
DashCommand
Are ceva mai puține funcții decât produsul anterior. Aplicația este capabilă să citească date de pe majoritatea dispozitivelor și componentelor mașinii și să le afișeze în grafice și vizualizatoare frumoase. Printre acestea, se poate evidenția funcționarea curentă a motorului, indicatorii economiei de combustibil, traseul. După diagnosticare, va afișa și coduri de eroare care vă vor ajuta să navigați în reparație. Se potrivește bine cu multe modele și variante ELM327.
Înainte de a utiliza ELM327 cu DashCommand, merită menționat faptul că aplicația conține conținut plătit. Îl puteți descărca din magazinul oficial Google Play.
OBD „AutoDoctor”
O diferență semnificativă față de programele anterioare este localizarea în limba rusă. Aplicația este gratuită, dar conține reclame.
Poate afișa în timp real citirile motorului, poate citi erorile și le poate șterge din ECU. Separat, merită evidențiat modul consolă, conceput pentru introducerea manuală a comenzilor specificațiilor ODB2.
De asemenea, știe cum să obțină parametrii sistemului GPS.
OpenDiag
Programul poate citi date de la senzorii mașinilor autohtone. Poate fi folosit la diverse servicii și stații de service. Capabil să arate erorile de bază și codurile acestora, informații actuale despre vehicul și parametri dinamici.
Înainte de a utiliza scanerul ELM327 cu Bluetooth și OpenDiag, dezvoltatorii recomandă să studiați cu atenție secțiunea de ajutor a aplicației, deoarece este posibil să nu fie acceptate toate dispozitivele.
ELM327 și Windows
De asemenea, scanerul nu a făcut fără adaptarea software-ului la sistemul de operare Windows. În continuare, va exista o mică listă de programe pentru conectarea și diagnosticarea mașinilor folosind linia Windows.
ScanMaster
Program funcțional și convenabil pentru mediul Windows. Poate afișa o mulțime de informații diferite de la senzori și noduri.
Interfața este concepută sub formă de diverse file, fiecare cu propriile sale funcționalități. Informațiile despre vehicul, de exemplu, vor afișa VIN și alte date numerice. Aici poți completa și tu un profil de mașină, dacă există mai multe dintre ele.
De cel mai mare interes pentru majoritatea proprietarilor de mașini va fi fila „Tabel cu date operaționale”. Reflectă mulți parametri și caracteristici în timp real într-o formă tabelară convenabilă.
Există și o altă filă interesantă - „Măsurări ale datelor operaționale”. Aici puteți specifica ceva din parametrii din paragraful anterior și puteți monitoriza modificarea acestora, de exemplu, atunci când conduceți o mașină.
„Codurile de eroare” vor afișa identificatorii defecțiunilor și imediat descrierea. Totuși, doar în engleză.
ScanTool
De fapt, este o versiune a ScanMaster, redusă în funcționalități și capacități. Dar ușor și receptiv. Dacă detaliile datelor nu contează cu adevărat, atunci aceasta este cea mai bună soluție.
PCMScan
Mai puternic decât ScanMaster. Pe lângă toate funcțiile deja enumerate, alte programe pot măsura puterea și cuplul actual al mașinii în timp real.
Programul poate fi conectat direct la monitorul din mașină pentru a vedea modificările și procesele care au loc în mașină.
De asemenea, este posibil să utilizați programul ca interfață de control pentru reglarea cipului. Din păcate, acest lucru necesită un modul special de la producător. Deși fără toate aceste clopoței și fluiere, programul își face față sarcinii cu o bubuitură. Înainte de a utiliza ELM327 mini împreună cu PCMScan, merită să studiați manualul în detaliu.
Alte aplicații de diagnosticare
Există și programe „ascuțite” pentru o anumită marcă de mașini. Dacă există o astfel de aplicație, atunci este mai bine să o utilizați. Programul va fi capabil să realizeze pe deplin potențialul scanerului, spre deosebire de soluțiile universale.
De exemplu, există un produs bun pentru Toyota - ELMScan Toyota.
Testarea testerului
Tautologia din titlu nu este întâmplătoare. Datorită numărului mare de modificări ELM, au apărut multe falsuri, versiuni și performanțe. Pentru a fi sigur de corectitudinea acțiunilor dumneavoastră, înainte de a utiliza autoscannerul ELM327, puteți afla ce versiune este.
Pentru aceasta există programul ELM327 Identifier. Verifică versiunea, afișează rezultatul pe ecran. Acest lucru va ajuta la rezolvarea problemelor de incompatibilitate ale unor module și software.
In cele din urma
Înainte de a utiliza scanerul ELM327, cel mai bine este să petreceți puțin timp și să vă dați seama cum să nu cumpărați un dispozitiv fals sau care nu este acceptat de sistemul de diagnosticare a mașinii. În plus, acesta este un dispozitiv electronic capabil să modifice unele date din ECU-ul mașinii, așa că alegerea trebuie luată cu multă responsabilitate.
Procedura de verificare a performanței unui motor de mașină poate fi efectuată atât vizual, cât și cu ajutorul unor echipamente suplimentare atunci când vine vorba de diagnosticarea computerizată. Unul dintre dispozitivele cu care puteți diagnostica funcționarea motorului este adaptorul ELM327. De ce ELM327 Bluetooth nu se conectează la situație? Vom discuta despre asta mai jos.
[Ascunde]
Motivele pentru care adaptorul refuză să se conecteze la ECU al mașinii
Dispozitivele de diagnosticare ELM327 sunt echipate cu o funcție Bluetooth, cu ajutorul căreia dispozitivul poate interacționa cu sistemul folosind două din șase protocoale. Adică, nu este necesar ca proprietarul mașinii să folosească un fir pentru a se conecta la ECU, deoarece poate fi furnizată o conexiune fără fir.
Adesea, proprietarii de mașini se confruntă cu problema incapacității de a conecta un dispozitiv cu un modul de control, de ce se întâmplă acest lucru:
- Ați achiziționat un adaptor de proastă calitate. În acest caz, nu vorbim despre firmware, ci despre inoperabilitatea umplerii hardware, aceasta este tipică pentru dispozitivele defecte. Dacă placa este nefuncțională sau inițial inoperabilă, atunci va fi imposibil să verificați performanța motorului. În consecință, cum să vă conectați la unitatea de control.
- Cablu deteriorat sau defect care împiedică comunicarea dispozitivului. Este necesar să se diagnosticheze firul pentru deteriorare.
- Un alt motiv pentru care conexiunea ar putea lipsi este din cauza firmware-ului slab. Dacă versiunea de software este prea veche, atunci va fi imposibil să sincronizați funcționarea dispozitivului cu mașina (autorul videoclipului este canalul KOLKHOZ).
Modalități de a rezolva problema pe cont propriu
Dacă sunteți sigur că versiunea de software funcționează, în special, vorbim despre firmware 1.5 și o versiune ulterioară, atunci puteți rezolva singur problema. Asigurați-vă că dispozitivul are toate cele 6 protocoale din 6. Conectarea la modulul de control al mașinii este posibilă folosind șiruri de inițializare, acest lucru va permite dispozitivului să se adapteze la comenzile ECU. În acest caz, ne referim la șirurile de inițializare pentru programele pentru verificarea Hob Drive și Torque.
Pentru a rezolva problema de conexiune, procedați după cum urmează:
- În primul rând, trebuie să conectați gadgetul la conectorul corespunzător, care se află în mașină. De obicei, în această etapă, proprietarii de mașini nu au probleme cu instalarea, dar în funcție de caracteristicile de proiectare ale vehiculului, este posibil să fie necesar să utilizați un adaptor. De regulă, acest conector este situat sub volan în habitaclu, în torpedo, în spatele sau sub acesta, uneori mufa este montată în zona brichetei. Puteți afla mai multe despre locație din documentația de service.
- După aceea, ar trebui să porniți motorul mașinii. Făcând acest lucru, veți vedea dacă computerul de bord detectează adaptorul conectat sau nu. Este important să porniți motorul și să nu puneți contactul.
- Următorul pas va fi sincronizarea dispozitivului cu un smartphone, iar acesta din urmă trebuie să funcționeze pe sistemul de operare Android. Pentru sincronizare, ambele gadgeturi sunt conectate printr-o conexiune wireless Bluetooth. Pentru a face acest lucru, accesați setările Bluetooth de pe telefon, activați opțiunea, apoi căutați toate dispozitivele din rețea. După ce telefonul detectează dispozitivul, acesta va trebui să fie conectat la acesta și trebuie utilizat un cod pentru a se conecta. Combinația poate fi diferită, dar, de regulă, acestea sunt numerele 0000, 1111, 1234, 6789.
- Dacă gadgetul se conectează cu succes la smartphone, atunci trebuie să lansați software-ul de verificare. Software-ul în sine trebuie configurat, ținând cont de parametrii performanței vehiculului. Pentru a configura, utilizați recomandările din instrucțiuni.
- În cazul în care toți pașii au fost executați corect, atunci software-ul ar trebui să înceapă verificarea. Cu ajutorul utilitarului, vi se vor furniza toate datele importante privind starea motorului, sistemele principale, precum și controlere și senzori. Dacă s-a întâmplat ceva că nu a fost posibilă sincronizarea dispozitivelor, atunci există și o cale de ieșire - trebuie să încercați să adăugați șirurile de inițializare necesare.
Trebuie avut în vedere că aceste linii sunt individuale pentru toate modelele de mașini și trebuie introduse manual în memorie. Aceste date sunt prezentate mai jos, dacă lipsesc unele rânduri, atunci pot fi găsite pe net fără probleme. Principalul lucru este că șirurile de inițializare se potrivesc exact cu modelul mașinii dvs., altfel dispozitivele nu se vor putea sincroniza.
OBD (On-Board Diagnostic) reprezintă diagnosticarea și controlul principalelor componente ale unui vehicul (șasiu, motor și unele dispozitive auxiliare). Pentru autoverificarea sistemelor, cel mai des este folosit adaptorul de diagnostic ELM327 - un dispozitiv compact care transmite date despre funcționarea unei mașini în timp real. Tot ce aveți nevoie pentru a utiliza ELM este un PC cu Windows, un telefon sau o tabletă Android sau iOS. Dacă vorbim despre cum să utilizați ELM327, atunci chiar și un proprietar de mașină începător poate face față conectării dispozitivului.
Cu toate acestea, înainte de a utiliza dispozitivul, trebuie să clarificați compatibilitatea scanerului de diagnosticare cu vehiculul dumneavoastră.
Cu ce mașini este compatibil scanerul?
Pentru a determina care autoscaner este potrivit pentru o mașină personală, este suficient să determinați protocoalele de comunicare. Pentru a face acest lucru, trebuie să vă uitați la conectorul OBD-2 și să clarificați ce contacte sunt prezente pe el:
- Prezența pinului 7 (K-Line) indică faptul că protocolul ISO 9141-2 este utilizat pentru diagnosticare. Acești conectori de diagnosticare sunt utilizați în vehiculele asiatice și europene.
- Constatările 4, 5, 7, 15 și 16 indică protocolul ISO14230-4KWP2000, care este utilizat în mod obișnuit pe Daewoo, KIA, Hyundai, Subaru STi și unele modele Mercedes.
În toate cazurile descrise mai sus, puteți utiliza în siguranță scanerul ELM327. În plus, va funcționa perfect cu protocoalele:
- SAE J1850 PWM / VPW;
- ISO 15765-4 CAN 29/11 biți 250/500 Kbaud;
- SAE J1939.
De regulă, autoscannerul ELM327 poate fi instalat și conectat cu ușurință la orice mașină.
Cum să vă conectați pe Android
Pentru a conecta scanerul ELM327, se folosește o priză specială, care se află sub blocul de direcție al mașinii (în habitaclu).
Sănătos! Dacă scanerul este instalat pe un VAZ și alte mașini domestice înainte de 2006, atunci cel mai probabil va trebui să utilizați un adaptor sau un adaptor.
- Descărcați micul utilitar Torque de pe Google Play. Această aplicație este considerată cea mai bună, deoarece vă permite să citiți suplimentar erorile sistemelor auto.
- Conectați ELM327 la conectorul corespunzător.
- Porniți motorul mașinii.
- Activați bluetooth pe dispozitivul dvs. mobil.
- Accesați setările smartphone-ului și accesați „Rețele wireless Bluetooth”.
- Faceți clic pe „Căutare echipament nou”.
- Așteptați până când lista dispozitivelor disponibile este afișată pe ecranul telefonului.
- Alegeți OBD 2 dintre ele și conectați-vă la el. Pentru a face acest lucru, trebuie să specificați un cod de împerechere special, cel mai adesea este 1234 sau 0000.
- Când conexiunea bluetooth ELM 327 este finalizată, puteți accesa setările. Pentru a face acest lucru, accesați Torque și selectați „Setări adaptor OBD 2”.
- Apoi, trebuie să selectați un dispozitiv Bluetooth, adică scanerul ELM 327 în sine.
După un timp, conexiunea va fi stabilită și va fi posibilă începerea diagnosticării sistemelor vehiculului.
Interfața programului
Dacă vorbim despre interfața ELM 327 OBD 2, atunci este intuitivă. După stabilirea conexiunii, trebuie să așteptați până când pictograma care clipește cu imaginea mașinii încetează să clipească. Dacă totul a fost corect, atunci dispozitivul va începe să funcționeze imediat.
Să ne dăm seama cum să folosim autoscannerul sau, mai degrabă, care dintre pictogramele programului Torque ne va interesa cel mai mult:
- Codul de eroare de verificare OBD - vă permite să citiți și să descifrați posibilele erori ale vehiculului.
- Informații în timp real - contoare care afișează parametrii motorului în timp real. Utilizatorul poate selecta și adăuga independent contoarele de care are nevoie. Pentru a face acest lucru, trebuie să faceți clic pe „Adăugați ecran”.
- Vizualizare hartă - afișează traseul de mișcare.
În timp ce mașina se mișcă, șoferul poate privi indicatoarele senzorilor de presiune, viteză, consum de combustibil și multe altele.
Dacă doriți să primiți date mai detaliate despre sistemele auto, este recomandat să vă conectați la scanerul ELM prin intermediul unui computer.
Cum să vă conectați pe Windows
Pentru a afla cum să conectați scanerul la un computer, trebuie să descărcați programul ScanMaster.
Sănătos! Înainte de a utiliza un program descărcat din rețea, acesta trebuie instalat corect. Pentru a face acest lucru, mai întâi găsiți un fișier numit „Key” sau „Keygen” și generați o cheie de acces. După aceea, puteți rula fișierul de instalare cu extensia „.exe”.
După aceea este necesar:
- Conectați scanerul la priza din mașină.
- Porniți motorul mașinii.
- Accesați panoul de control al computerului și accesați secțiunea „Dispozitive Bluetooth”.
- Faceți clic pe „Adăugați dispozitiv” și bifați caseta de lângă „Dispozitivul este gata de descoperit” și selectați „Următorul”.
- Căutarea dispozitivelor disponibile va fi efectuată o perioadă de timp, după care autoscannerul se va conecta la laptop.
- Faceți clic din nou pe „Următorul”.
- În fereastra care apare, trebuie să conduceți cu unul dintre codurile standard: 0000, 1111, 1234 sau 6789.
- Faceți clic din nou pe „Următorul”.
- Așteptați integrarea automată a dispozitivului cu computerul și faceți clic pe „Finish”.
Aceasta completează instalarea software-ului scanerului.
Dacă ești un fan înfocat al produselor Apple, iar opțiunea de conectare la un PC sau smartphone Android nu ți se potrivește, atunci ar trebui să achiziționezi un model special ELM 327 Wi-Fi, care poate fi conectat la orice dispozitiv iOS.
Cum să vă conectați la iPhone sau iPad
Pentru a obține propriul centru de diagnosticare pentru a testa funcționarea unui vehicul, nu este necesar să vă conectați la scaner prin bluetooth. Modelele ELM mai moderne sunt echipate cu un modul Wi-Fi care vă permite să utilizați aproape orice dispozitiv portabil pentru a primi date.
Să vedem cum să stabilim o astfel de conexiune:
- Conectați scanerul la conectorul din mașină.
- Accesați secțiunea responsabilă pentru setările conexiunii fără fir și selectați rețeaua „CLKDevices”.
- Va fi o săgeată albastră în dreapta, pe care trebuie să se apasă.
- În fereastra care apare, trebuie să introduceți datele adresei IP și ale routerului: 192.168.0.11. De asemenea, trebuie să specificați masca de subrețea implicită: 255.255.255.0.
- Mai jos trebuie să specificați portul 35000.
Aceasta încheie setarea. Știind cum să folosești scanerul ELM 327, este suficient să instalezi orice aplicație pentru diagnosticare rapidă și să înregistrezi aceiași parametri IP și porturi în setările sale.
Cu toate acestea, trebuie avut în vedere faptul că poate fi dificil să configurați scanere private.
Cele mai frecvente erori de conectare
Probleme care pot apărea la conectare:
- Scanerul nu se conectează la ECU. Acest lucru se poate întâmpla din mai multe motive: dispozitivul nu este potrivit pentru marca / modelul mașinii, adaptorul sau programul este selectat incorect. Uneori, șoferul uită să treacă prin inițializare. Mai rar, conexiunea nu are loc din cauza unei defecțiuni mecanice banale - siguranța s-a defectat, care este responsabilă pentru funcționarea conectorului OBD II.
- ELM327 nu afișează date în timp real (de exemplu, consumul de combustibil). Faptul este că această funcție este disponibilă numai în timp ce vehiculul este în mișcare.
- Scanerul automat nu citește și nu șterge erorile. Adesea este nevoie de un motor în funcțiune pentru a activa un dispozitiv, așa că este suficient să porniți pur și simplu motorul. Unele modele ieftine ELM327 nu știu cum să resetați erorile ABS, acest lucru poate fi rezolvat, dar dispozitivul trebuie modificat.
In custodie
ELM327 este un dispozitiv compact care va economisi semnificativ la diagnosticarea mașinii, este ușor de utilizat și vă permite să afișați date pe aproape orice PC sau telefon. Cu toate acestea, înainte de a conecta singur autoscannerul, merită să studiați videoclipul, care arată clar procesul de utilizare a ELM.
Scanerul automat de diagnosticare Bluetooth ELM327 este proiectat pentru instalare pe toate tipurile de mașini echipate cu conectori standard OBD2 cu 16 pini. Vă rugăm să rețineți că scanerul ELM327 vine cu două tipuri de firmware - 1.5 și 2.1. Dispozitivele cu firmware 1.5 pot funcționa cu ECU-uri de viteză redusă, precum și cu conectori non-standard, pe lângă conectorul obdii.
Scanerul ELM327 este conceput pentru a găsi și elimina problemele din sistemele electronice ale mașinii, precum și pentru a afișa diferiți parametri ai motorului și ai mașinii pe dispozitivul mobil al proprietarului.
Conținutul livrării
Dispozitivul este livrat cu următoarea configurație:
- Adaptorul scaner Bluetooth ELM327 conectat la sistemul de bord prin conectorul obdii.
- Disc de instalare cu software.
- O carte de vizită care indică arhiva completă cu instrucțiuni și programe rusești pentru scaner.
Specificații scanerului
Scanerul automat Bluetooth ELM327 acceptă următoarele protocoale de comunicare atunci când este conectat la conectorul OBD2:
- ISO15765-4 (autobuz CAN): mașini Audi, Volvo, Chrysler, Mazda, Mitsubishi, Opel, Peugeot, Porsche, Renault, Saab, Volkswagen, Ford, Jaguar.
- ISO14230-4 (KWP2000): Daewoo, Hyundai, KIA.
- ISO9141-2: Audi, BMW, Infiniti, Lexus, Mercedes, Nissan, Porsche, Toyota, Honda.
- J1850 VPW: Buick, General Motors, Dodge, Isuzu, Cadillac, Chrysler, Chevrolet.
- J1850 PWM: Lincoln, Mazda, Ford.
Cum să vă conectați și să lucrați cu dispozitivul
Scanerul automat de diagnosticare Bluetooth ELM327 comunică cu computerul de bord al mașinii prin conectorul OBD2. După introducerea în conector, dispozitivul se conectează prin Bluetooth cu dispozitivul mobil al proprietarului mașinii.
Vă rugăm să rețineți că dispozitivul dvs. mobil trebuie să ruleze pe sistemul de operare Android, deoarece pentru acest sistem de operare a fost dezvoltat un program special pentru transferul datelor de la scaner pe dispozitivul mobil. Software-ul Torque este furnizat împreună cu scanerul pe un disc separat. Acesta este programul care va afișa toate erorile detectate, va evidenția citirile senzorului.
Când conectați ELM327 la rețeaua internă a mașinii, trebuie să deblocați telefonul și să activați programul Torque. Când porniți programul pentru prima dată, trebuie să stabiliți o conexiune stabilă între scanerul Bluetooth ELM327 și programul specificat. Pentru a face acest lucru, aveți nevoie de:
- Intrați în secțiunea Bluetooth și porniți-o.
- Apoi activați „Căutați rețele noi”. Telefonul ar trebui să găsească „Dispozitiv nou”.
- Atingeți această linie dacă aveți un dispozitiv mobil cu ecran tactil sau treceți cursorul de activare peste acesta dacă aveți un telefon fără ecran tactil.
- Mini scanerul de diagnosticare ELM327 este autorizat automat pe dispozitivul dvs. mobil.
Vă rugăm să rețineți că există două tipuri de configurații de scaner - o carcasă albastră (este mai compactă) și o carcasă neagră (un dispozitiv mai mare). Scanerul albastru se autentifică fără parole, în timp ce scanerul negru are trei opțiuni de parolă prestabilite:
- 1234;
- 0000;
- 6789.
Ultima parolă este cel mai puțin probabil să fie găsită ca prestabilită pe scaner.
1. După ce scanerul de diagnosticare este autorizat pe dispozitivul dvs. mobil, accesați programul Torque.
Vă rugăm să rețineți că o conexiune stabilă cu computerul de bord este stabilită în program prin logo-ul albastru al mașinii stilizate. Dacă acest logo nu se aprinde, atunci trebuie să:
- Mergi la Setari";
- Accesați „Setări adaptor OBD2”;
- Accesați „Selectați un dispozitiv Bluetooth” (situat în partea de sus a listei);
- Selectați „dispozitiv obdii” și puneți un punct în fața acestuia.
Vă rugăm să rețineți că această secvență de pași va asigura o conexiune stabilă pe dispozitivele mobile Samsung. Poate că, pe dispozitivele mobile de la alți producători, secvența specificată va fi diferită.
2. Testați funcționarea corectă a scanerului. Pentru a face acest lucru, este suficient să adăugați pur și simplu gaz la mașină, astfel încât motorul să crească numărul de rotații. Această acțiune ar trebui să fie afișată imediat în program: săgeata stilizată a tahometrului va indica cât de mult a crescut turația motorului.
Funcționalitatea programului Torque
Programul Torque are o gamă foarte largă de posibilități, dar următoarele funcții vor fi cele mai utile șoferului:
1. Erori de citire.
Dacă semnul Verificare se aprinde pe tabloul de bord, înseamnă că electronicele mașinii dumneavoastră au un fel de problemă. Pentru a le identifica, trebuie să mergeți la secțiunea „Erori de citire” și să activați funcția de căutare a erorilor. Scanerul automat ELM327 găsește erori în electronice și afișează codurile acestora pe smartphone prin Bluetooth. Folosind aceste coduri, puteți utiliza internetul pentru a determina exact ce probleme s-au întâmplat în sistemul electronic al mașinii dumneavoastră.
Dar cel mai important, programul vă va oferi opțiunea „Ștergeți eroarea”. Cu alte cuvinte, dispozitivul va încerca să remedieze singur problema și să raporteze rezultatele. Acest lucru vă va scuti de reparațiile costisitoare și reglarea electronicelor auto la stația de service.
2. Tabloul de bord.
În această secțiune veți găsi un număr mare de senzori diferiți. Apropo, puteți alege cum sunt afișate:
- scară cu o săgeată (vitezometru tradițional sau cerc tahometru cu o săgeată analogică);
- scară;
- jumătate din scară cu o săgeată;
- jumătate din scară;
- Panou de afișare;
- programa.
Alegerea diferitelor măsurători ale performanței mașinii nu este mai puțin variată. De exemplu, puteți selecta următorii indicatori de performanță a motorului și a vehiculului:
- Presiunea atmosferică;
- echilibrarea combustibilului;
- timpul de călătorie (timp de călătorie);
- timp de calatorie;
- timpul de călătorie (de la începutul călătoriei);
- timpul de funcționare după pornirea motorului;
- ora sosirii la ¼ și 1/8 mile;
- senzor de accelerație;
- barometru;
- pozitia clapetei de acceleratie;
- emisiile curente și medii de dioxid de carbon;
- presiunea galeriei de admisie;
- presiunea combustibilului;
- combustibil consumat în timpul călătoriei;
- consum de combustibil pentru moment, km/l;
- consum mediu de combustibil pe călătorie, km/l;
- sarcina și turația motorului;
- Debitul masei de aer;
- temperatura aerului de admisie;
- sincronizarea aprinderii;
- viteza vehiculului;
- starea sistemului de combustibil;
- temperatura agentului de răcire.
După ce ați selectat unul dintre indicatori, programul vă va solicita să selectați dimensiunea senzorului - de la mic la foarte mare.
Diagnosticarea funcționării autovehiculului este un proces important, deoarece cu ajutorul acestuia puteți afla în funcționarea ce părți ale mașinii există probleme. Unul dintre dispozitivele de diagnosticare auto este un adaptor. Din ce motive ELM327 Bluetooth nu se conectează la ECU și ce să faci în astfel de cazuri? Vom discuta despre asta mai jos.
[Ascunde]
De ce refuză adaptorul să se conecteze la ECU-ul mașinii?
Deci, de ce ELM327 nu vede ECU? Ce ar trebui să fac pentru ca dispozitivul să se poată conecta și să vadă blocul? Astăzi, la vânzare, puteți găsi multe adaptoare diferite pentru testarea unui vehicul. Dacă cumpărați ELM327 Bluetooth, sunt șanse să încercați să conectați dispozitive de calitate scăzută. Mai degrabă, este posibil să fi achiziționat un adaptor cu o versiune de software învechită.
Dispozitivele Bluetooth ELM327 cu firmware învechit utilizează un modul Bluetooth diferit care permite interacțiunea cu două dintre cele șase protocoale disponibile. În consecință, este posibil să sincronizați dispozitivul cu un smartphone, dar atunci când încercați să conectați dispozitivul la unitatea de control, acesta vă va informa că.
Deci, din ce motive dispozitivul refuză să se conecteze la bloc:
- Adaptorul în sine este de proastă calitate. Problemele pot fi atât cu firmware-ul dispozitivului, cât și cu hardware-ul acestuia. Dacă microcircuitul principal este inoperant, va fi imposibil să se diagnosticheze funcționarea motorului, precum și să se conecteze la ECU.
- Cablu de conectare prost. Cablul poate fi rupt sau este inoperabil singur.
- Versiunea software greșită este instalată pe dispozitiv, drept urmare sincronizarea nu va funcționa (autorul videoclipului despre testarea dispozitivului este Rus Radarov).
Cum să rezolvi singur problema?
În cazul în care sunteți proprietarul unui dispozitiv cu versiunea corectă de firmware 1.5, unde toate cele șase dintre cele șase protocoale sunt prezente, dar adaptorul nu se conectează la ECU, există o cale de ieșire. Vă puteți conecta la bloc folosind șiruri de inițializare, care permit dispozitivului să se adapteze la comenzile unității de control al motorului mașinii. În special, vorbim despre șiruri de inițializare pentru utilitățile de diagnosticare HobDrive și Torque pentru vehiculele care folosesc protocoale de conectare non-standard.
După cum știți, adaptoarele de acest tip fac posibilă conectarea la unitatea de control în majoritatea vehiculelor de fabricație străină fabricate după 1996. Deci, cum rezolvi singur problema?
În primul rând, trebuie să conectați corect adaptorul:
- În primul rând, este necesar să conectați dispozitivul la priza computerului de bord al vehiculului. De regulă, proprietarii de mașini nu au probleme de conectare, dar la unele modele de mașini, trebuie să utilizați suplimentar adaptoare. În cele mai multe cazuri, priza pentru conectare se află sub volanul mașinii, uneori se află în torpedo sau sub ea. De asemenea, conectorul poate fi situat lângă brichetă.
- În plus, este necesar să porniți motorul mașinii - nu să porniți contactul, ci să îl porniți. În funcție de modelul mașinii, este posibil ca unitatea de control să nu vadă adaptorul fără a porni motorul.
- După aceea, trebuie să sincronizați adaptorul cu un gadget mobil pe platforma Android, pentru aceasta, se utilizează o conexiune fără fir Bluetooth. Pentru a face acest lucru, accesați configurația Bluetooth și activați mai întâi funcția, apoi căutați elementele disponibile. Când adaptorul este găsit, trebuie să vă conectați la el, pentru a vă conecta se folosește un cod special. Poate fi 0000, 1111, 1234 sau 6789.
- Când dispozitivul este conectat cu succes la gadgetul mobil, trebuie să mergeți la utilitar. În program, ar trebui să găsiți configurația și să o configurați în conformitate cu toți parametrii necesari, în funcție de mașină. Procedura de configurare poate diferi în funcție de software, dar principiul este același peste tot. Trebuie să găsiți un adaptor care să fie sincronizat cu telefonul mobil.
- Dacă ați făcut totul corect, atunci utilitarul ar trebui să înceapă să funcționeze. Veți putea citi toate informațiile necesare despre funcționarea echipamentelor, sistemelor și senzorilor. Dar dacă sincronizarea a eșuat, atunci puteți încerca să rezolvați problema adăugând șiruri de inițializare. Șirurile de inițializare sunt individuale pentru fiecare model de vehicul individual - sunt adăugate manual. Lista cu șirurile de inițializare care trebuie introduse la conectarea echipamentului este dată mai jos. Pentru ca rezultatul să fie corect, este necesar să adăugați în memorie doar acele linii care corespund exact modelului vehiculului.
Șiruri de inițializare pentru gadget