Qarqet praktike të amplifikatorëve të tubave duke përdorur transformatorë TN
Skema 1. Përforcues me dy tuba duke përdorur 6F3P ose 6F5P triod-pentodë.
Skema është klasike dhe nuk kërkon një përshkrim të hollësishëm të fizikës së funksionimit të saj.
Një fazë diferenciale përdoret si një fazë paraprake e përforcimit dhe refleks bas. Rryma e anodës së çdo triode është 1.45 mA. Në këtë rast, fitimi i kaskadës nga hyrja në çdo dalje është 25. Ndjeshmëria e amplifikatorit nga hyrja, në fuqinë maksimale të daljes, është vlera efektive 0,45 volt.
Faza e daljes së amplifikatorit funksionon me paragjykim automatik në modalitetin e klasës AB. Bilanci aktual i llambave të daljes përcaktohet nga një ndryshim i vogël (plus/minus 1,5 volt) në paragjykimet e tyre të rrjetit.
Furnizimi me energji elektrike është bërë në bazë të transformatorëve standardë TAN me një ndreqës gjysmëpërçues të urës dhe një filtër klasik C-L-C në formë U. Për llambat "rrymë" me tension të ulët, preferohet përdorimi i diodave gjysmëpërçuese në ndreqës në vend të kenotroneve.
Parametrat e amplifikatorit për këtë qark janë dhënë në dy rreshtat e parë të tabelës 4.
Zëvendësimi i 6F3P me 6F5P nuk do të çojë në një ndryshim në qark, përveç se do t'ju duhet të ribashkoni instalimet elektrike të paneleve dhe të ndizni mbështjelljet e transformatorit të daljes. Është gjithashtu e mundur të përdoren pentoda "të vetme" 6P18P, 6P43P në këtë qark dhe të kryhet faza diferenciale e inverterit të fazës në një triodë të dyfishtë 6N23P. Një diagram i tillë është paraqitur në figurën e mëposhtme. Këtu, përdoret një seri e ndryshme transformatorësh furnizimi dhe prestazhi vendoset në dyfishin e tensionit të furnizimit të anodës për një linearitet më të mirë.
Skema 2. Përforcues me tre tuba për 6N23P dhe 6P43P ose 6P18P.
Qarku është plotësisht i ngjashëm me atë të mëparshëm, me ndryshimin e vetëm që faza diferenciale paraprake është bërë në një triodë të dyfishtë 6N23P. Rryma e anodës së çdo triode është 6.25 mA. Fitimi i një qarku të tillë nga hyrja në secilën prej daljeve parafazore është 14. Prandaj, ndjeshmëria e amplifikatorit nga hyrja, në fuqinë maksimale të daljes, është vlera efektive 0,8 volt.
Nëse dëshironi të furnizoni një sinjal hyrës parafazor për amplifikatorët sipas skemave 1 dhe 2, duhet të aplikoni një sinjal të anasjelltë në rrjetin e triodës së dytë përmes kondensatorit të disponueshëm në qark (0,47 μF) duke shkëputur terminalin e tij të poshtëm në qarku nga autobusi i përbashkët. Në këtë rast, ndjeshmëria e amplifikatorit për çdo hyrje do të jetë 2 x 0.4 volt. Në skemën 1, ndjeshmëria e amplifikatorit me një sinjal parafazor do të jetë 2 x 0,225 volt.
Furnizimi me energji elektrike në elementët e tij përbërës është plotësisht i ngjashëm me qarkun e mëparshëm, megjithatë, fizika e funksionimit të tij është e ndryshme. Prestazhi ushqehet me një tension të rritur prej + 370 volt nga ndreqësi i urës për të siguruar linearitet më të madh të fitimit dhe simetri më të mirë të qarkut për shkak të vlerës së madhe të rezistencës në qarkun e përbashkët të katodës dhe, në përputhje me rrethanat, një rënie të madhe të tensionit në të (+ 70 volt). Faza e daljes mundësohet nga një ndreqës me valë të plotë të formuar nga dy dioda urë me anode të tokëzuara dhe një potencial prej +200 volt nxirret nga mesi i mbështjelljes së anodës. Filtri anti-aliasing është i ngjashëm me skemën e mëparshme.
Gama e frekuencës në gjysmë fuqie (voltazh 0,707) nga 40 Hz në 25 KHz.
Ndjeshmëria e amplifikatorit në fuqinë maksimale të daljes është 0,25 ... 0,3 volt.
Parametrat e ndryshueshëm të amplifikatorëve sipas skemave 1 dhe 2 janë përmbledhur në tabelën 4.
Tabela 4.
Llambat | Dalja tr-r. | Fuqia tr-r. | Pout [W] | Raa [Ohm] | Ea [V] | Iao | - P.sh. 1 [V] | Rk [Ohm] | Rc [Ohm] |
6F3P | TN33, 36 | TAN2, 14, 28, 42 | 9 | 5000 | 220 | 2 x 32 | 16 | 270 | 240 |
6F5P | TN36, 39 | TAN2, 14, 28, 42 | 14 | 4050 | 220 | 2 x 40 | 20 | 120 | 270 |
6P18P | TN36, 39 | TAN4, 17, 31, 45 | 9 | 5600 | 200 | 2 x 60 | 11 | 330 | 75 |
6P43P | TN36, 39 | TAN4, 17, 31, 45 | 15 | 3333 | 200 | 2 x 60 | 16 | 330 | 130 |
Skema 3. Push-pull ULF në llambat "televizive".
Parapërforcuesi në këtë qark përbëhet nga dy faza. Mënyra e fazës së parë të amplifikimit në pjesën e triodës së 6F1P u zgjodh afër asaj standarde me një rrymë anode prej 10 mA dhe një tension anodë prej 93 volt. Fitimi i fazës 7.
Inverteri i fazës është bërë sipas qarkut të një amplifikuesi diferencial parafazor bazuar në një triodë të dyfishtë 6N23P me një burim rrymë në një qark të përbashkët katodë. Pjesa pentode e llambës 6F1P u përdor si burim rrymë. Skema e kaskadës diferenciale është plotësisht e ngjashme me atë të mëparshme. Rryma e anodës së çdo triode është 6.25 mA. Fitimi është 14. Kështu, faktori total i para-fitimit do të jetë 98.
Ndjeshmëria e UMZCH sipas skemës 3 në fuqinë maksimale të daljes do të jetë vlera efektive 0,23 volt.
Meqenëse tensionet e furnizimit të anodës së amplifikatorëve me VT janë të fiksuara dhe të përcaktuara në mënyrë të ngurtë nga llogaritjet e mësipërme, dhe parametrat e llambave "kornizë" dhe "linjë" janë kryesisht të qëndrueshme, duket e mundur të zhvillohet një qark i vetëm amplifikator për 6P36S, 6P41S. 6P42S, 6P44S, 6P45S. Vetëm parametrat e disa elementëve pasivë, përfshirja e mbështjelljeve dytësore dhe vlerësimet e tipit të transformatorëve të fuqisë dhe daljes do të jenë të ndryshme. Epo, sigurisht, rrymat e konsumuara nga burimi i energjisë dhe fuqitë dalëse të amplifikatorëve do të jenë gjithashtu dukshëm të ndryshme.
Si një ndreqës i furnizimit me anodë për një përforcues që përdor tubat aktualë, është më mirë të përdorni një urë gjysmëpërçuese, pas së cilës është instaluar një filtër zbutës C-L-C. Ky qark, krahasuar me një ndreqës kenotron, do të sigurojë stabilitet më të mirë të tensionit të ulët të anodës në rrymat e ngarkesës së lartë. Dhe rrymat e anodës në këta amplifikues do të jenë shumë domethënëse. Një rezistencë 1 kilo-ohm në terminalin negativ të urës anode kufizon rrymën e ngarkimit të kondensatorëve të filtrit dhe duhet të lidhet me qark të shkurtër pas ndezjes së amplifikatorit, por jo më herët se pas 5 sekondash.
Parametrat e ndryshueshëm të amplifikatorëve sipas skemës 3 janë përmbledhur në tabelën 5
Tabela 5.
Llambat | Transformatori i daljes | Transformatori i fuqisë | Puth. [W] | Raa [Ohm] | Ea [V] | Iao | - P.sh. 1 [V] | Rg [Kohm] | Sf [µF] |
6P41S | TN42, 44, 46, 47 | TAN31, 45 | 28 | 1620 | 200 | 2 x 70 | 27 | 27 | 330 |
6P36S | TN49, 50, 52 | TAN45, 59 | 32 | 1400 | 200 | 2 x 60 | 24 | 20 | 470 |
6P44S | TN54, 56, 57 | TAN73 | 43 | 1040 | 200 | 2 x 100 | 33 | 43 | 470 |
6P42S | TN58, 59 | TAN73, 108 | 49 | 920 | 200 | 2 x 100 | 33 | 43 | 680 |
6P45S | TN60, 61 | TAN108 | 56 | 800 | 200 | 2 x 150 | 37 | 68 | 680 |
Një version i amplifikatorit duke përdorur tubat 6P44S tregohet në diagramin më poshtë. Bilanci i qarkut të fazës së daljes rregullohet brenda kufijve të vegjël duke përdorur një potenciometër në rrjetat e ekranit. Pasi të keni vendosur më parë të njëjtat rryma të llambës në modalitetin e pushimit me këtë rezistencë, rregullimi përfundimtar i simetrisë së qarkut duhet të kryhet në një sinjal nominal me një minimum të shtrembërimeve jolineare.
Kur instaloni amplifikatorë, është e nevojshme të mbani mend se transformatorët e blinduar TAN31, 45, 59 dhe transformatorët e shufrës TAN73, 108 kanë numra të ndryshëm pin.
Mund të provoni gjithashtu lidhjen me triodë për llambat aktuale duke lidhur rrjetin e ekranit me anodën; për fat të mirë, mënyra e tyre tipike siguron të njëjtat tensione furnizimi për anodën dhe rrjetin e ekranit.
Ju gjithashtu mund të kaloni fazën e daljes në modalitetin e klasës A me paragjykim automatik - me një rezistencë të përbashkët në katodë prej 140 Ohms për 6P44S (6.6 W do të shpërndahen nga kjo rezistencë, kështu që ju duhet të lidhni katër rezistorë 2 vat prej 560 Ohm paralelisht), natyrisht, duke rregulluar furnizimin me energji të anodës në këto 30 volt, duke lidhur në seri me mbështjelljet e anodës mbështjelljet e paragjykimit të lirë 11-12 dhe 20-21. Kështu, me paragjykim automatik, voltazhi i furnizimit të anodës do të rritet në afërsisht 230 volt. Sidoqoftë, do t'ju duhet të kontrolloni tensionin e furnizimit me parastage për t'u siguruar që nuk e kalon kufirin 450 volt për kondensatorët elektrolitikë. Tensioni i tepërt do të absorbohet nga një rezistencë 10 kilo-ohm 1-vat e lidhur direkt me terminalin pozitiv të urës anode përpara se ta lidhni atë me kondensatorin e filtrit. Një lidhje e ngjashme e një rezistence shuarjeje tregohet në Diagramin 2.
I njëjti qark amplifikator do të sigurojë fitimin dhe gamën e nevojshme të tensionit të daljes së inverterit fazor për drejtimin e llambave "rregulluese" të llojeve 6S19P, 6S41S, 6S33S. Por kjo është tema e një prej artikujve pasues.
Transformatorët TN hapin mundësi të mëdha të projektimit të qarkut në projektimin e amplifikatorëve të tubave shtytës, madje deri në riprodhimin e zërit me cilësi të lartë.
Eksperimento!
Përshëndetje miq! Unë dua t'ju tregoj për krijimin e tubit tim ULF në 6P36S. Ky është një shtytje-tërheqje me një kompensim fiks sipas skemës së S. Sergeev.
Ishte në pushimet verore, kishte shumë kohë, kishte njohuri, kishte dëshirë. Kështu që vendosa të bëj një lloj amplifikuesi stereo tub për të dëgjuar muzikë. Po, po, ishte ai tub, kurrë nuk më pëlqyen "gurët".
Fillova të mendoj se çfarë qarku të marr, me çfarë llambash? Vendosa të zgjidhja diçka nga llambat që kisha. Për disa arsye nuk doja të përdorja llambat 6P15P dhe 6P43P. Po shqyrtoja opsionin 6P13S, por lexova një përmbledhje negative. Në fund u vendosa në 6P36S. Më pëlqeu edhe pamja e saj: kaq e madhe dhe mbresëlënëse. Dhe vlerësimet në lidhje me të janë pozitive.
Qarku i amplifikatorit të tubit nga S. Sergeev
Fuqia e lartë dhe prania e tubave të përshtatshëm në fazën e shoferit më bindi të ndërtoj shtytjen time të parë.Përforcuesi tingëllon shumë mirë dhe ka parametrat e mëposhtëm:
Tensioni i furnizimit 360 volt
Konsumi i energjisë nga rrjeti 170 W
Ndjeshmëria 0.7 Volt
Fuqia dalëse 40 W
I armatosur me një listë pjesësh, shkova në treg. Fatkeqësisht, ky është i vetmi vend ku mund të blini pjesë radio në qytetin tim.
Transformatori i fuqisë TSA-270
Si një transformator furnizimi, doja të përdorja një transformator standard të pashpërthyer, për shembull TS-180. Më gjetën vetëm TCA-270, të cilin e bleva dhe shkova në shtëpi, mjaft i kënaqur. Edhe pse dredha-dredha është alumini (indeksi A), ai siguron parametrat e pasaportës.E lidha TCA-270 si kjo:
Përfundimet 7-17 përdoret për të marrë tensionin e paragjykimit të një kanali
Përfundimet 4-14 për furnizimin me anodë të një kanali
Përfundimet 11-(21-12)-22 për filamentin 6P36S të një kanali. Terminalet 20-(10-10')-20' në inkandeshencë 6N1P të të dy kanaleve.
Dredhat që kam dhënë sigurojnë saktësisht tensionin dhe rrymën e kërkuar.
Transformatori i daljes TS-180
Kam përdorur një TS-180 si një transformator dalës dhe e lidha atë sipas qarkut të propozuar nga Manakov.Bordi i montimit në sipërfaqe
Unë do të doja të tërhiqja vëmendjen tuaj në mënyrën time jo standarde të krijimit të tabelave. Fakti është që unë nuk e gërmoj vulën, e pres letrën në PCB në katrorë me përmasa 2 cm x 1 cm dhe nxjerr një diagram për instalimin e pjesëve. Për shembull:
Diagrami sipas të cilit i bashkova pjesët në tabelë.
Linjat midis katrorëve janë kërcyes. Ka edhe lidhje më të gjata, ato vizatohen si vija. Shigjetat në katrorë tregojnë vendin në të cilin do të bashkohen telat nga panelet e llambave, ose fuqia, etj. Për shembull, 3L1 do të thotë se kunja e 3-të e llambës së parë (6N1P) është ngjitur atje, 8L2 do të thotë se kunja e 8-të e llambës së dytë (6P36S) është ngjitur atje. Ato. shifra e parë është numri i pinit, letra thjesht ndahet dhe shifra e dytë është numri i llambës.
Nuk po ju sugjeroj të bëni të njëjtën gjë, thjesht kjo metodë është e thjeshtë dhe kursen kohë dhe para. Rezulton të jetë një "kulm" në PCB.
Këtu është bordi që kam
Fillimi i parë
Lëshimi i parë ishte i suksesshëm. Ka vetëm një keqardhje: në atë kohë nuk kisha një multimetër në dorë. E vjetra është prishur, nuk kam blerë ende të re. Në përgjithësi, e vendosa duke përdorur një metodë barbare: rregullova kompensimin në mënyrë që të ishte minimale, por anodat nuk u kthyen në të kuqe.Gjithçka duket se po funksionon, është koha për ta fshehur atë në këtë rast. Dhe atëherë isha shumë me fat: një i njohur i babait tim më dha një kitarë të vjetër që nuk funksiononte ULF "Minor", e cila u shkul menjëherë.
Rasti nga "Minor" përshtatet në mënyrë të përsosur, dy transformatorë dalës TS180 (të shtrirë) dhe 2 dërrasa të vetë ULF përshtaten në të, por transformatori i energjisë TCA-270 nuk u përshtat. Prandaj, u bë një rast i veçantë për furnizimin me energji elektrike nga chipboard dhe kompensatë. Pjesa e sipërme e trupit është e mbuluar me shirit vetëngjitës.
Janë shpuar vrima për panelet. Gjithçka është instaluar, dhe tani nisja e shumëpritur në rast. E ndez dhe... gati sa nuk shurdhesha nga bilbili teksa u ngrohën llambat! Duke mallkuar, fik energjinë dhe shkoj në treg për të blerë një tel të mbrojtur, duke e blerë me rezervë.
Luftimi i zgjimit - mbrojtjes
Për të eliminuar vetë-ngacmimin, i cili manifestohet si një bilbil, ishte e nevojshme të mbroheshin qarqet e rrjetit të triodës 6N1P dhe telat në qarqet e rrjetit të dy 6P36S. Anodat 6P36S nuk ishin të mbrojtura. Fishkëllima pushoi.E nis përsëri dhe dëgjoj: një kanal funksionon shkëlqyeshëm, por në tjetrin ka klikime në vend të basit, plus një rangun e mesëm të ngadaltë dhe të ngjirur. Sigurisht që u mërzita në këtë pikë. Dhe çfarë nuk kam provuar? arsyeja rezultoi të ishte skanimi i gabuar i rrjetës. Ekranet nuk ishin të tokëzuara siç duhet.
Unë e ribëra atë, i tokëzova skajet e ekraneve me një yll - kjo është kur të gjitha telat shkojnë në një pikë dhe në trup. Ndërhyrja dhe eksitimi u zhdukën, klikimet në bas u ndalën, basi u bë i qartë, elastik dhe të dy kanalet filluan të këndojnë njëlloj bukur.
Detajet
Në amplifikator kam përdorur rezistorë MLT dhe OMLT me fuqi 1-2 Watts. Bleva të gjitha rezistorët me fuqi 1-2 Watts. Kondensatorët C3 dhe C4 janë të tipit K73-17, dhe C2 u furnizua nga BMT-2. Unë kam një llambë 6N1P në shofer, e cila mund të zëvendësohet me një 6N23P pa asnjë modifikim në qark. Por më pëlqen më shumë tingulli i 6N1P.Tubat e daljes 6P36S, për të rritur fuqinë e amplifikatorit, mund të zëvendësohen me 6P42S, duke vendosur një rrymë qetësie më të lartë, diku rreth 106 mA (rënie nëpër rezistorët e katodës 1.06 V)
Cilësimet dhe veçoritë e fiksuara të kompensimit
Pas blerjes së multimetrit, konfigurimi u bë i lehtë, pajisja është në gjendje pune dhe gati: rezistenca R9 vendosi të njëjtin tension në katodën e llambave, dhe rezistenca e paragjykimit vendosi tensionin në 0,55 Volt.Sidoqoftë, ekziston një veçori e pakëndshme e një kompensimi fiks. Kur ndryshon voltazhi i rrjetit, modaliteti i llambës ndryshon. Sapo voltazhi në rrjet u rrit në 250 V dhe një 6P36S doli nga modaliteti, anoda u nxeh, rryma e qetë u rrit në 80 mA (me 55 mA të përshkruara)! Për fat të mirë, e vura re këtë menjëherë dhe e fika ULF.
Më duhej të instaloja një stabilizues të tensionit "Ukrainë-3", imi prodhon 215 V. Për shkak të tensionit të pamjaftueshëm në primar (dhe, në përputhje me rrethanat, në sekondar), tensionet në anodat ranë nga 330 V e kërkuar në 313 V. E ngrita rrymën qetësuese në 64 mA (rënie në rezistorët R12, R13 = 0,64 V).
6P45S është një llambë shumë e konsumit! Për një bandura kaq të shëndetshme, është bërë shumë keq! Së pari, ekziston një gamë e gjerë parametrash. Së dyti, katoda dhe terminali janë të lidhur shumë keq, të mbërthyer me një tel të vogël që digjet në çdo mbitension. Kam vidhos rreth 5 llampa.Vetëm katoda e dy prej tyre nuk u dogj menjëherë, u dogj...në një ditë! Dhe vetëm një funksionoi për një muaj.Për të shmangur shkrirjen, doja të paralelizoja dy prej tyre, por rryma e filamentit prej 5 A më dukej shumë e lartë. Unë i përdora ato në konvertuesin tim të tubit të tensionit të lartë:
http://stalin.flyback.org.ru/tubeflyback.htm
Pastaj instalova një 36 në vend të 45, gjithçka ka funksionuar për rreth një muaj, 36 në fakt mban me qetësi 600 (!) volt dhe 30 vat në anodë. I besueshëm si shkëmb (në një mënyrë të mirë).
Arkadi Antonov
> Fuqia e anodës 6p36s-20 watts
Mund të jetë kështu, por llamba mban me qetësi 27 - 28 vat në anodë... Po, dhe tridhjetë nuk do ta trembin atë
Nga përvoja ime, 36 tingëllon më bindëse (kundrejt 45)
Pronin
Tetrodat e kornizës me tingullin më të mirë, për mendimin tonë, janë llambat 6P42S PA ANODE DHOMA. Megjithatë, ato janë jashtëzakonisht të rralla, dhe kuptimi i prodhimit të tyre në Svetlana në 1972-1975 është përgjithësisht i paqartë. Sidoqoftë, ato ekzistojnë, mund t'i gjeni. Gjithashtu shumë të mira janë 6P36S dhe 6P42 me një anodë të bardhë "me gëzof". Ata janë gjithashtu absolutisht "të pathyeshëm", me sa duket për shkak të veshjes së anodës.
Karakteristikat e zërit të këtyre llambave varen shumë nga mënyrat e përdorura.
Prandaj, është e vështirë të flitet për tingullin jashtë këtyre lidhjeve "mode".
> Dhe gjithsesi, cilat janë kufijtë për 36 dhe 42?
Më pëlqen modaliteti 300 V, 125 mA për 6P42S dhe 300 V, 72 mA për 6P36S.
Ngarkesa është absolutisht e saktë - përkatësisht 2 dhe 4 com.
Mund ta mbyllni në 2 com, të vendosni dy priza dhe të dëgjoni paralelisht një 6P42S ose dy 6P36S.
Nuk ka nevojë të vendosni 5Ts3S, tingulli do të jetë muzikor, por i ngadaltë. Instaloni dy 6D22S dhe arrini muzikalitet duke zgjedhur pjesë.
Dhe në çdo rast, nuk ka asnjë pikë për të ngarkuar kenotron në hapësirë.
Shalin
Epo, a mundet dikush të më thotë modalitetet optimale për këtë tub në një triodë dhe rezistencën e brendshme dhe Mu në pikën e funksionimit... Unë jam hutuar - kam dëgjuar përforcuesin në këto tuba, dhe ata luajnë më mirë se EL34 dhe shumë më mirë se EL84 me dizajn identik të qarkut. Ndryshe nga 6P45S, ata ruajnë në mënyrë të qëndrueshme modalitetin pa lundruar në rryma termike me një zhvendosje fikse. Epo, në përgjithësi, bëni gjithçka që mundeni për të ndihmuar. Me sa kuptoj, nuk ka grafikë anodë për këtë llambë në natyrë - unë nuk kam as "ministri" në librin tim të referencës.
Gajdar
Atëherë është më mirë të përdorni 6P36S. Ajo luan edhe më mirë se 6P44S
Shalin
> Përshëndetje Alexey. Meqenëse jeni në forum, më tregoni modalitetin për SE 6P36S dhe
> ngarkesa e dhënë ose disa opsione. Faleminderit Eduard.
Për 6P36S: 330 V, 70 mA, Ra = 5 com.
Më pëlqen kjo mënyrë
Shalin
> Vetëm 6P36S është i ngjashëm me 6P42S të lëshimeve të para.
> Dhe 6P36S kanë më pak përhapje dhe janë më të qëndrueshme.
Dhe sot u binda për këtë - thjesht po zgjidhja çifte nga 6p36:
Ne arritëm të zgjidhnim nga 15 copë
1 palë perfekte
1 kuartet i papërsosur
4 llamba të përshpejtuara
Epo, 5 pjesë janë krejtësisht të ndryshme.
Rendimenti 40% është një rezultat i mirë
Dhe ky çift ideal tingëllon shumë bukur.
Mjekër
Ka Svetlanov dhe Ulyanovsk 6P36S me anoda gri të lehta - ato luajnë më mirë se thjesht ato gri.
Shalin
Më mirë me "42". Anoda 42 është pak më e madhe se e 36-ta dhe e ngjashme me të, dhe e 45-ta është
1.5 herë më e lartë dhe në skajet në të dyja anët ka tre vrima drejtkëndëshe përafërsisht 6x6 mm. Duket se A. Shalin ka postuar diku foto të sakta 42. 36 kështu - nëse anoda është pothuajse e bardhë dhe "me gëzof" ose gri e çelur dhe përsëri "me gëzof" - atëherë duhet ta ruani atë, qoftë edhe të përdorur.
HRYUN
Duhet ta ndizni për 2-3 minuta, aq sa llamba të ngrohet. Ata ndihen normal. Kjo nuk është ende mbinxehje serioze. Dyzet e pesë është një zonjë e fortë. Ata vetëm i mbledhin ato dobët.
Kuptimi i një kontrolli të tillë është si më poshtë. Në një tetrode me rreze, të dy rrjetat kanë të njëjtin hap dhe duhet të instalohen në mënyrë që fijet e rrjetës të jenë saktësisht përballë njëra-tjetrës. Kështu formohen rrezet. 6P45S dhe 6P36S kanë pothuajse të njëjtin dizajn të rrjetës katodë - 4 korniza me tela të salduar. Dy korniza në njërën anë të katodës, dy në anën tjetër. Rezulton dy grupe rrezesh në drejtime të ndryshme nga katoda, në gjysmat e kundërta të anodës. Le të supozojmë se në njërën anë kornizat nuk janë të rreshtuara saktësisht. Atëherë rryma e rrezes në këtë anë do të jetë më e vogël se në anën tjetër, dhe gjysma e anodës në këtë anë do të nxehet më pak se e kundërta. Gjysma e llambës është një tetrode rreze, dhe gjysma është një konvencionale. Dhe këto dy tetroda, të ndryshme në karakteristika, janë të lidhura paralelisht. Në parim, mund të përdorni një pirometër për të matur temperaturën e pjesëve të ndryshme të anodës, por në mungesë të një, ngrohni llambën për një kohë të shkurtër derisa të shfaqet skuqja. Nëse merr ngjyrë të kuqe më shumë nga njëra anë, kjo është një shenjë e qartë e një defekti në prodhim. Do të funksionojë mirë në skanimin horizontal, por është më mirë të mos e përdorni në tingull. Ka afërsisht 80-90% të llambave të tilla me defekt.
Oleg
Mesazh nga KHRUN
Dhe e vërteta është Tmerr...! Unë do t'ju tregoj sekretin tim të tmerrshëm: disi (shumë më parë)
6P36S im (vintage) ka punuar për një kohë mjaft të gjatë në modalitetin 250 V,
160 mA (40 vat, megjithatë...) me paragjykim automatik (më saktë, pothuajse me rregullim automatik, por atëherë askush nuk e dinte që ishte auto-rregullim). Dhe asgjë, ata mbetën të gjallë... Gridlik ishte, me sa duket, 51 kOhm.
Po kështu. Vetëm Svetlanov 6P36S im i përdorur funksionoi për disa muaj në modalitetin 100 mA 400V dhe me rregullim.
Dalka
Dhe pikerisht kjo eshte arsyeja e tingullit te keq... Kam hasur ne 45 qe beheshin te kuqe nga njera ane ne 40 vat tek anoda, ndoshta pak me shume. Ata u larguan menjëherë nga plehrat. Sa fuqi mund të shpërndajë llamba e zgjedhur përpara se të kthehet në të kuqe?
Sergej Z
Ata të përzgjedhur në 60 praktikisht nuk kthehen në të kuqe. Vetëm në errësirë të plotë vihet re një shkëlqim i lehtë. Në të vërtetë, kjo është një alternativë e mirë për 6S33S. Është shumë më e lehtë për tu lëkundur dhe shumë më lineare.
Oleg
Shikova kthesat e triodës I-V të 45-tës.
Kam gjetur një mënyrë:
250V, 180mA, -50V në rrjet.
Ri = 290 ohms, Ra = 2380 ohms, alfa = 8,2.
Uam = 181 v, Iam = 76 mA,
P~ = 6,88 W.
Lineariteti në këtë mënyrë është shumë i lartë.
Në modalitetin 250 V, 240 mA, nuk do të jetë e mundur të bëhet një ngarkesë prej më shumë se 1242 ohms, pasi atëherë gjysma e djathtë e linjës së ngarkesës do të shkojë edhe përtej kurbës së fuqisë prej 60 (!!!) vat.
Me një fjalë, çfarëdo që mund të thuhet, përdorimi i 6P45S me fuqi anode më shumë se 45 W është i dyshimtë për mua...
Shalin
6P36S janë llamba shumë rezistente ndaj dridhjeve me rrjeta të forta kornizë, ato kanë një mikrofon të vogël.
Shalin
IMHO, në krahasim me 6P36s, 6P44S së pari mahnitet nga risia e tingullit, pastaj, pasi dëgjon,
ju e kuptoni që tingulli është "me gjemba dhe i ashpër", por subjektivisht ka më shumë lartësi,
kur matej një bisht më i gjatë harmonike, u kryen vetëm matje krahasuese
një fazë dalëse në llamba të ndryshme, të gjitha gjërat e tjera janë të barabarta.
Sa i përket përhapjes, Svetlanov 6P44S ka parametra më të afërt se 6P36S,
për 6P44S përhapja mesatare është deri në 30-35%, 6P36S deri në 50%.
Gjithçka mësohet me krahasim, por më së shumti kanë 6P31S të zgjedhura, IMHO të papërdorura më parë
tingull natyral, afër tingullit 2A3 në rangun e mesëm dhe trefishtë.
Manakov
Dmitry, një nga amplifikatorët e mi 6P36S ka punuar për 8 vjet me 20 vat në anodat pa zëvendësuar llambat. Shoku im ka tre vjet në 27 volt.
Diku Hryun vuri në dukje se në modalitetin e detyruar (36 watts në anodë) Ri e 6P36S bie në 450 ohms.
Unë vetë përpiqem të mos "torturoj" 6P36S me më shumë se 28 vat.
Shalin
Dmitry, kjo do të thotë që llambat nuk ishin shumë të mira
6P36S i mirë sillet në mënyrë të përsosur me 33-100 ohmë në rrjet. Por masat kundër eksitimit janë patjetër të nevojshme, kjo është e vërtetë.
Unë nuk e kam testuar 6P36S me më shumë se 32-33 vat fuqi anode, por shoku im në amplifikator me një 6P36S (ndërtimi im) e kallajoi me 37 vat, dhe jeton normalisht me një fiksues dhe madje pa një cung anodë.
Shalin
Ndër krijuesit e amplifikatorëve të tubave, tubat që janë përdorur më parë në televizorë janë me meritë të njohura. 6N23P, 6F3P, 6P45S janë ende shumë të njohura në mesin e prodhuesve të amplifikatorëve dhe kjo nuk është një listë e plotë e llambave të tilla. Midis këtyre llambave ka liderë në popullaritet, si llambat dalëse, për shembull, më të njohurit janë 6P36S dhe 6P42S, dhe ky popullaritet është i merituar. Kur performohet mirë, tingulli i amplifikatorëve në këto tuba kënaq veshët e mprehtë të shumë adhuruesve të muzikës.
Më poshtë është një nga versionet e një amplifikuesi me një skaj me një tub dalje 6P42S.
Për të ndezur plotësisht 6P42S, ju nevojitet një sinjal me një amplitudë prej 70-80 Volt. Është mjaft problematike të merret një amplitudë e tillë duke përdorur një drejtues me një fazë nga një burim sinjali standard. Prandaj, u vendos që shoferi të bëhej me dy faza, në fazën e parë E80CC performoi shumë mirë, në fazën e dytë u vendosëm në EL84 në lidhjen me triodë, megjithëse 6P15P dhe EL803 performuan shumë mirë.
Faza e daljes përdor një transformator me një mbështjellje katodë, e cila rrit linearitetin e fazës dhe zvogëlon rezistencën e saj në dalje. Qarku i amplifikatorit është paraqitur në Fig. 1.
Fig. 1 Diagrami skematik i amplifikatorit elektrik
Siç mund të shihet nga diagrami, 6P42S përdoret me një paragjykim fiks. Si një sensor i rrymës së anodës, unë zakonisht përdor rezistencën aktive të mbështjelljes së katodës, zakonisht është rreth 10 Ohms.
Amplifikatori ndizet në tre faza: kur ndizet çelësi i përgjithshëm 1, të gjitha fijet nxehen paraprakisht, pas së cilës kontaktet e stafetës 2 mbyllin një rezistencë kufizuese prej 1 kOhm dhe llambat nxehen plotësisht dhe në anodën furnizojnë tensionin. rritet afërsisht në gjysmë. Pas mbylljes së kontakteve të releit 3, aplikohet tension i plotë i anodës dhe amplifikatori është gati për funksionim.
Transformatori i daljes ka një rezistencë të reduktuar (për mbështjelljet e anodës dhe katodës së bashku) prej rreth 2.5 kOhm, mbështjellja e katodës është afërsisht 10% e mbështjelljes së anodës.
Tani në lidhje me tubat e daljes. Ekzistojnë të paktën katër modele të ndryshme të këtyre tubave, ku dy më të hershmet janë më "tingëlluesit", me vrima të rrumbullakëta në anodë. Më e mira ka një anodë gri-argjendi, e dyta në renditje ka një anodë gri të miut. Dallimi në tingullin e tyre është shumë i vogël në favor të atij të argjendtë. Versioni i fundit është i ngjashëm në dizajn me 6P45S dhe tingëllon në përputhje me rrethanat.
Përforcuesi origjinal përdori rezistorë BC (përveç anodës EL84, ka Matsushita me pesë vat, një në një të njëjtë si Kiwame, por blu), kondensatorë elektrolitikë Tesla, kondensatorë ndërfazë - K40-U9, kontrolli i volumit - tela PPZ- 40. Por kjo nuk është dogmë.
Si përfundim në lidhje me karakteristikat e matura: fuqia maksimale e daljes ishte 11 W me një gamë frekuencash prej 8 Hz...50,000 Hz (me një sheshit prej ±3 dB) dhe 16...35,000 (me një nivel prej ±0,5 dB) , Kni = 1% (me 8 W), Rout = 1,5 Ohm.
Dizajni i amplifikatorit është paraqitur në Fig. 2. Nuk ka asnjë rrjet mbrojtës në foto, i cili është instaluar për arsye sigurie, sepse tensioni kërcënues për jetën është i pranishëm dhe lehtësisht i aksesueshëm në kapakët e anodës 6P42S.
Urat e diodës në ndreqësit e furnizimit me energji janë të njëjta. Në një farë mase, kjo është për shkak të përdorimit të kondensatorëve të ruajtjes me kapacitet të lartë në to. Në ndreqës, mund të përdorni një urë diodë VD3 me një vlerë kufi më të ulët të rrymës (për shembull, seri
KTs402), por në këtë rast një rezistencë kufizuese e rrymës me një rezistencë prej 80 ... 100 Ohms duhet të lidhet në seri me dredha-dredha (5-15).
Tifoz (është i vendosur në panelin e pasmë të kasës - shih paraqitjen e njësive dhe paneleve në Fig. 3) për ventilim të detyruar (shter) - pothuajse çdo nga një furnizim me energji kompjuteri komutues, por nëse është e mundur është më mirë të zgjidhni një me një nivel më të ulët të zhurmës akustike.
Furnizimi me energji elektrike përdor mbytëse të përdorura në televizorët e vjetër me tub, por mund të përdorni të tjera që janë të përshtatshme për parametrat. Induktiviteti i mbytjeve L1, L2 është 0,4 H dhe L3 është 5 H.
Lloje të ndryshme pjesësh mund të përdoren në amplifikator: rezistorë - MLT, MON, BC me fuqi të përshtatshme me një tolerancë jo më shumë se 10%; kondensatorë jopolarë - film polietileni tereftalat K73-9, K73-16 ose K73-17 për një tension prej të paktën 400 V. Lejohet gjithashtu instalimi i kondensatorëve letre nga pajisjet e vjetra - KBG-I, BMT-2, K40U- 9, MBM. Kondensatorët e oksidit në furnizimin me energji dhe përforcues importohen nga Jamicon ose seritë vendase K50-35, K50-26, K50-27.
Treguesit e nivelit të sinjalit në secilin prej kanaleve (PA1) janë shigjeta (M42305 ose të ngjashme për 50-200 µA). Në thelb, ata kryejnë një funksion ndihmës dhe sjellin estetikisht disa dinamikë në funksionimin e pajisjes. Ndriçimi i treguesit mund të organizohet duke përdorur LED ose llamba inkandeshente në miniaturë të mundësuar nga një burim tensioni 12 V në furnizimin me energji elektrike.
Amplifikatori ka një dizajn unik. Në pjesën e poshtme ka një furnizim me energji elektrike të montuar në shasinë e vet; në krye është blloku i amplifikatorit (dy kanale), gjithashtu në një shasi të veçantë (shih Fig. 3).
Amplifikatori përdor një kontroll të volumit me një motor elektrik stereo ALPS RK27 100 kOhm (Blue Velvet); kjo ju lejon të lidhni një telekomandë me tela, e cila ka një çelës dypolësh (ndërprerës) me tre pozicione fikse (SA1 në diagramin në Fig. 2). Një tjetër opsion i mundshëm është një levë, e cila, në varësi të drejtimit të devijimit të saj, lidh motorin elektrik me një burim tensioni 12 V duke përdorur grupe kontakti bipolare në polaritetin e duhur (mund të përdorni gjithashtu reletë elektromagnetike të përshtatshme, për shembull, RES22 ose të ngjashme) * Megjithatë, telekomanda jo domosdoshmërisht - kjo është në një farë mase një haraç për modën
Vëmendje e veçantë duhet t'i kushtohet prodhimit të kasës.Duke qenë se amplifikatori funksionon në kushte të vështira temperaturash, druri duhet fillimisht të thahet mirë.Në këtë rast, dërrasat janë tharë natyrshëm në kushte dhome për 6 muaj. Pas përfundimit të dërrasave, prej tyre u bë një trup (foto në Fig. 4). Boshllëqet janë prerë në skajet në një kënd prej 45° dhe janë ngjitur së bashku me ngjitësin “Joiner-moment”, pas kësaj trupi është vendosur pranë radiatorit të ngrohjes qendrore dhe është mbuluar me një batanije. Në këtë gjendje, u la të thahej edhe për dy muaj të tjerë, pas së cilës u prenë vrimat dhe dritaret e nevojshme dhe u ngjitën elementët dekorativë të paneleve të përparme, të sipërme dhe të pasme. Pas këtyre operacioneve, trupi për një muaj
U thava përsëri pranë radiatorit, i mbuluar me një batanije. Më pas është bërë lëmimi dhe lyerja me përbërjen lyerëse Belinka-TOPLAZUR në ngjyrë sofër (Nr. 28) në katër shtresa. E gjithë kjo është bërë në mënyrë që të mos ketë surpriza në të ardhmen gjatë funksionimit të amplifikatorit.
Përforcuesi ka një regjim mjaft intensiv të temperaturës në pjesën e sipërme të kasës, ndërsa pjesa e poshtme pothuajse nuk nxehet. Materiali trupor i tharë në mënyrë të pamjaftueshme (në këtë rast, pisha) mund të shpërthejë përgjatë kokrrës. Më është dashur të punoj shumë për të marrë një rezultat të mirë: prej tre vitesh nuk ka asnjë ankesë për rastin. Nëse nuk doni të bëni shufra, trupi mund të bëhet nga kompensatë 15...20 mm e trashë, e mbuluar me rimeso.
Panelet anësore të kutisë janë prerë nga xhami i lyer "Turquoise" me trashësi 5-6 mm. Kur amplifikatori është në punë, ato mund të zhvendosen pak mbrapa, siç tregohet në foton në Fig. 5; ndërsa ventilimi
byk do të përmirësohet ndjeshëm. Për ta bërë jetën më të lehtë të amplifikatorit, një ftohës kompjuteri është instaluar në panelin e pasmë, që funksionon në dy mënyra - në 8 dhe 12 V. Mund të ndizet ose fiket nëse dëshironi
Panelet e pasme dhe të përparme janë të prera nga alumini 2...3 mm, të lyer me rërë dhe të veshura me llak akrilik të pastër automobilistik nga paketimi aerosol.
Vrima me diametër 5...6 mm janë shpuar rreth paneleve të llambave për të siguruar konvekcion natyral të ajrit. Paneli i sipërm i kasës ka një grilë metalike mbrojtëse, e cila futet lirshëm në kornizën dekorative të këtij paneli
Në këtë model të amplifikatorit, transformatorët e daljes nuk janë mjaft konvencionalë. Ato janë bërë në bazë të një transformatori rrjeti TS-90 me një bërthamë magnetike ShL. Të gjitha mbështjelljet hiqen nga bobinat standarde dhe të rejat mbështillen në masë me një tufë prej nëntë telash PELSHO. Nga këto, shtatë PELSHO-0.33 telat përdoren në dredha-dredha parësore, dhe dy tela PELSHO-0.8 - në atë sekondar. Diagrami i lidhjes së këtyre telave në mbështjellje është paraqitur në Fig. 6.
Një tufë prej këtyre nëntë telave, rreth 10 m të gjatë, mbështillet në kornizën e çdo bobine derisa të mbushet (përftohen rreth 70 rrotullime) Më pas, këto bobina zihen në parafinë për 15...20 minuta në një ujë. banjë C
Opsionet e transformatorit të daljes janë gjithashtu të mundshme. Llambat 6P36S kanë një rezistencë të brendshme mjaft të ulët, dhe për një përforcues shtytës që përdor llamba të tilla, nga 700 në 1000 rrotullime të mbështjelljes primare (për qarkun magnetik të përdorur) me një trokitje nga mesi është mjaftueshëm.
Amplifikatori dhe furnizimi me energji elektrike janë të pajisur me pllaka qarku të bëra prej tekstil me fije qelqi të veshur me fletë metalike. Për shkak të faktit se ato kanë një model shumë të thjeshtë, ai pritet me një prestar të bërë nga një teh sharrë hekuri. Një pamje e instalimit të pjesëve dhe montimeve të vogla në shasinë e blloqeve është paraqitur në foto fig. 7.
Në panelin e pasmë të kutisë ka terminale dalëse për të dy kanalet, lidhësit e hyrjes, lidhësin e telekomandës, lidhësin e rrjetit, çelësin e ventilatorit (çelësi i kuq), çelësin e modalitetit të ventilatorit - çelësin e ndërrimit (tensioni 8 ose 12 V) , një terminal tokësor i kasës dhe një bllok siguresash (një në qarkun e rrjetit primar dhe dy në qarqet e furnizimit me anodë të secilit kanal)
Nga redaktori. Në rastin kur ventilatori ndodhet poshtë llambave të fuqishme, ventilimi i detyruar duhet të organizohet si ventilim furnizimi.
Komentet për artikullin: