Sistemul de iluminat cu fibra optica pentru o baie este unul dintre cele mai eficiente, durabile si sigure. Fiecare proprietar poate alege componentele pentru instalarea sa și finaliza instalarea. Recomandările noastre vă vor ajuta să înțelegeți procesul.
Conţinut:
Organizarea iluminatului în saună cu ajutorul fibrei optice a devenit recent din ce în ce mai populară. Astfel de lămpi pentru baie cu fibră optică sunt mult mai funcționale, mai sigure și mai economice decât sursele de lumină tradiționale. Sunt potrivite optim pentru instalarea în baia de aburi, toaletă și încăperi auxiliare.
Caracteristici de iluminare cu fibră optică în baie
Datorită caracteristicilor lor operaționale și tehnice ridicate, aceste lămpi sunt adesea instalate în băile de aburi. Printre principalele avantaje ale acestor structuri se numără:
- Stabilitate termică. Fibra optică este capabilă să funcționeze la temperaturi de până la +200 de grade. Prin urmare, poate fi montat chiar și pe tavanul băii de aburi, unde de obicei se menține cea mai ridicată temperatură.
- rezistenta la umezeala. Sistemul de fibra optica este folosit pentru iluminarea piscinei datorita rezistentei sale la umiditate ridicata.
- Lumina slaba. O astfel de lampă nu trebuie să instaleze abajururi suplimentare. Lumina sa este difuză, nu rănește ochii.
- compactitatea. Sistemul de iluminat poate fi montat direct în carcasă. Nu este nevoie să îi aloci un loc special.
- Siguranță. Fibra optică conduce doar radiația (nu curentul) și, prin urmare, instalarea ei în baia de aburi este absolut sigură. Datorită specificului de fixare pe un mănunchi de fibre, este imposibil să fii ars.
- Durabilitate. Înlocuirea acestui tip de iluminare de fundal trebuie să fie efectuată mult mai puțin frecvent decât omologii săi.
- Ușor de instalat. Instalarea proiectorului, a lentilelor și a fibrelor se poate face manual, chiar și fără abilități tehnice speciale.
- O abundență de soluții de proiectare. Cu ajutorul unui garou, puteți crea o animație a cerului înstelat, aurore boreale, foc, valuri, furtuni. Setul include duze de diferite culori care pot schimba panta luminii pentru a întruchipa idei de stil originale. In plus, garoul este flexibil, ceea ce iti permite sa ii dai forma dorita.
- economie. Fibra optică consumă mult mai puțină energie decât alte tipuri de iluminat.
Dezavantajele unor astfel de lămpi includ un cost relativ ridicat.
Elemente ale unui sistem de iluminat cu fibră optică pentru o baie
Iluminarea cu fibra optica completa, spectaculoasa si placuta pentru o baie poate fi creata prin completarea fibrelor cu cristale si lentile speciale. Combinația de pachete optice cu alte tipuri de iluminare, de exemplu, LED, va arăta originală. În baia de aburi, elementele principale, cum ar fi rafturile și băncile, sunt tăiate cu ghidaje de lumină.
Puteți cumpăra lămpi cu fibră optică pentru baie ca set sau puteți selecta separat componentele sistemului:
- Proiector. Cantitatea de lumină emisă depinde de puterea acesteia. Aparatul folosește lămpi cu halogen de 12 V. Fiecare dintre ele consumă 50 V și are o putere de lumină ridicată.
- fibre. Cantitatea de lumină emisă depinde și de diametrul acestora. Cu selecția corectă, puteți crea iluminare direcțională, generală sau de accent în baie. Pentru instalarea într-o baie de aburi, ar trebui să alegeți modele într-un pahar, nu o carcasă de plastic. Funcționează mai bine la temperaturi ridicate și rezistă mai ușor la picături. Când alegeți, rețineți că există mănunchiuri de strălucire laterală și de capăt. Primul tip poate fi împletit și poate crea modele ușoare. Al doilea este setat punctual, de exemplu, imitând cerul înstelat.
- Produsele finite. Acestea sunt lentile, lămpi și cristale care sunt fixate pe marginile ghidurilor de lumină. De ei va depinde direcția luminii, luminozitatea acesteia. În mod tradițional, capătul fibrei împrăștie lumina la un unghi de 40-60 de grade. Dacă atașați un accesoriu de lentilă, atunci unghiul de refracție poate ajunge la 20-25 de grade. Când utilizați duze decorative din cristal, lumina este focalizată într-un fascicul la un unghi de 180 de grade sau mai mult.
- Accesorii. Discurile colorate vă permit să creați o imitație originală de strălucire și strălucire în cameră.
Sistem de iluminat lateral cu fibra optica in baie
Principiul de funcționare a unui astfel de sistem de iluminat este extrem de simplu: proiectorul este instalat în afara băii de aburi, un mănunchi de fibre transmite lumină purificată de radiațiile infraroșii și ultraviolete. Instalarea o puteți realiza singur, deoarece nu necesită pregătirea circuitelor electrice.
Pentru a face acest lucru, acționăm în următoarea secvență:
- Montam un proiector in dressing. Alegeți un loc lângă peretele care mărginește baia de aburi. Ar trebui să fie amplasat la o distanță sigură de sursa de căldură dacă se află în aceeași cameră.
- Instalăm discuri color pe proiector dacă se dorește.
- Marcăm în camera de aburi locurile de instalare a ghidajelor de lumină, după o schemă pregătită în prealabil.
- Fixăm elementele de fibră optică cu segmente. Vă rugăm să rețineți că fibra conține un miez flexibil de ghidare a luminii cu un indice de refracție ridicat. Dacă trebuie tăiat, atunci facem această procedură numai cu un cuțit fierbinte, după care șlefuim cu grijă tăietura, astfel încât să se dovedească a fi o oglindă.
- Dacă se dorește, dotăm sistemul cu duze de culoare a lentilelor. Puteți controla acest efect manual sau automat. În acest din urmă caz, instalăm suplimentar un comutator.
Sistem de fibre optice de strălucire finală pentru o baie
Înainte de a începe lucrul, trebuie să creați un aspect al elementelor punctuale din cameră. Este mai bine să montați un astfel de iluminat înainte de decorarea interioară.
Lucrăm în această ordine:
- De la proiector măsuram distanța până la fiecare punct al strălucirii și tăiem mănunchiurile de lungimea corespunzătoare.
- Așezăm fibrele, fixându-le temporar cu bandă adezivă.
- În punctele de ieșire, instalăm diblurile astfel încât să iasă 2-3 cm în afară. Le atașăm hamurile folosind sârmă sau cleme. Acest lucru este necesar pentru a respecta modelul și fixarea verticală a locației.
- Învelim suprafața, îndepărtând diblurile inutile și banda adezivă.
- Tăiem fibra la nivelul pielii și o șlefuim cu hârtie de șlefuit cu granulație fină.
- Tăiem și șlefuim capetele inverse, le asamblam într-un conector și le conectăm la proiector.
După aceeași schemă, ghidajele de lumină pot fi montate în departamentul de spălare. Dacă are o piscină, atunci acest tip de iluminat va arăta foarte impresionant în partea de jos. În camera de odihnă, lămpile cu fibră optică pot fi combinate cu alte corpuri de iluminat. Conductele de lumină din această cameră pot fi folosite pentru a ilumina elemente individuale, cum ar fi o oglindă sau tavan. Cu ajutorul lor, poți crea atmosfera optimă pentru relaxare.
Urmăriți videoclipul despre sistemul de iluminat cu fibră optică:
Nu este dificil să instalați lămpi cu fibră optică pentru o baie cu propriile mâini în baia de aburi. Principalul lucru este să urmați instrucțiunile și să alegeți componentele potrivite.
Este foarte dificil să proiectați și să aranjați iluminatul în baia de aburi. La urma urmei, umiditatea ridicată, abundența de abur și temperaturile ridicate nu sunt în totalitate favorabile pentru utilizarea energiei electrice. În ciuda acestui fapt, iluminatul cu fibră optică a devenit din ce în ce mai popular. Utilizarea sa este relevantă nu numai pentru o baie, un ham optic este folosit chiar și într-un apartament și o casă. Acest lucru se datorează faptului că o astfel de lumină este mult mai economică și mai sigură decât sursele de lumină standard, în plus, vă permite să faceți o iluminare decorativă a camerei. În acest articol, vă vom spune cum să realizați iluminatul cu fibră optică cu propriile mâini, oferind o diagramă de conectare a sistemului, precum și instrucțiuni de instalare.
În ce constă sistemul?
De regulă, astfel de sisteme sunt vândute ca un set, în care este deja inclus tot ce aveți nevoie. Dar, pe lângă componentele principale, puteți adăuga elemente suplimentare care vor ajuta la crearea unui interior individual. Aceasta, de exemplu, este o iluminare specială folosind o bandă LED sau lentile sau cristale speciale.
Iluminatul cu fibră optică include următoarele componente:
- Proiector. Din întregul sistem, doar el este conectat la electricitate. Cantitatea de lumină emisă depinde de puterea dispozitivului.
- fibre. Datorită acestor elemente, puteți, de asemenea, să reglați cantitatea de lumină care este eliberată și să o distribuiți pe întregul perimetru al băii la discreția dvs. Atunci când alegeți un garou, este mai bine să acordați preferință modelului de sticlă, deoarece este mai rezistent la schimbările de temperatură. Există două tipuri de pachete: strălucire laterală (crearea de modele luminoase folosind împletirea fibrelor) și strălucire finală (se creează cerul înstelat).
- Lentile și lămpi. Iluminatul cu fibră optică cu ajutorul unor astfel de elemente capătă o strălucire direcțională. La urma urmei, aceste lentile și cristale sunt cele care reglează dispersia și direcția fluxului de lumină.
Atunci când alegeți un sistem de fibră optică, ar trebui să acordați atenție nu numai lungimii și numărului de fibre, ci și la care lampă este utilizată. Atât lămpile cu halogen, cât și cele cu descărcare necesită răcire și, deoarece unele sisteme de răcire au ventilatoare zgomotoase, acest lucru vă poate strica vacanța.
Metoda de strălucire laterală
O astfel de iluminare se poate face manual, deoarece nu necesită circuite electronice complexe. Instalarea este simplă: instalați doar proiectorul în afara saunei. Acest lucru se face după cum urmează:
- Un proiector este instalat în camera din fața băii. Locul unde este montat trebuie să fie lângă baia de aburi (să aibă un perete comun). Dacă proiectorul este instalat în aceeași cameră, ar trebui să fie departe de sursa de căldură.
- Dacă doriți, puteți instala accesorii suplimentare pe dispozitiv, de exemplu, discuri color.
- Conform diagramei, marcați locurile unde va fi plasată fibra.
- Instalarea iluminatului cu fibra optica.
- Dacă doriți, puteți instala duze de culoare (lentile sau cristale). Conectarea acestui efect poate fi fie automată, fie manuală.
Important! La instalarea fibrei optice, este necesar să se țină cont de îndoirea permisă a fiecărei fibre optice. Depinde de diametru. Prin urmare, distanța focală a produselor ar trebui să fie mai mare de 85%. Toate acestea sunt gândite bine atunci când este întocmită diagrama sistemului.
Metoda de strălucire a marginilor
Este mai bine să efectuați instalarea unei astfel de lumini înainte de decorarea interioară. În primul rând, ar trebui să întocmiți un aspect exact al elementelor punctuale.
Instalarea iluminatului cu fibră optică trebuie făcută în următoarea ordine:
- Tăiați frânghiile la lungimea necesară. Și pentru a afla lungimea, ar trebui să măsurați distanța de la proiector până la toate punctele de strălucire.
- Așezați fibrele la locul lor, mai întâi fixați-le cu bandă adezivă.
- Pentru a păstra modelul și a fixa fasciculele pe verticală, este necesar să instalați dibluri în anumite locuri de care sunt atașate fibrele cu ajutorul unui fir. Pentru a-l atașa a fost convenabil, diblurile ar trebui să iasă trei centimetri spre exterior.
- Suprafața este învelită și toate benzile și diblurile inutile sunt îndepărtate.
- Apoi trebuie să tăiați mănunchiul de fibre. Acest lucru se face în funcție de nivelul pielii. Apoi, șlefuiți capetele pachetului cu hârtie de șlefuit cu granulație fină.
- Celelalte capete ale fibrei sunt conectate la un conector și conectate la proiector.
În timpul instalării, este necesar să monitorizați cu atenție curbele ghidajelor de lumină. La finalizarea instalării, se pot adăuga diferite lentile și cristale la sistem, dacă se dorește.
O astfel de schemă de conectare pentru iluminatul cu fibră optică este potrivită și pentru departamentul de spălare. Mai ales dacă există o piscină acolo, atunci o astfel de iluminare va arăta foarte bine în partea de jos. Într-un lounge, sufragerie sau dormitor, corpurile de iluminat cu fibră optică pot fi combinate cu corpuri de iluminat standard. Atmosfera creată în acest fel va ajuta la relaxare.
Literal, în ultimele două decenii, dispozitivele computerizate pentru comunicare, comunicare, muncă sau divertisment au apărut în aproape fiecare familie. Conexiunile abonaților se fac prin linii telefonice, canale radio și fibra optică a fost utilizată pe scară largă în ultima perioadă.
A trebuit să evaluez posibilitățile acestei tehnologii din propria mea experiență. Pe baza acestuia, public sfaturi pentru un maestru acasă despre conectarea computerului la Internet printr-un cablu de fibră optică și crearea unei rețele de apartament cu fir și fără fir cu imagini explicative, diagrame și un videoclip.
Prima expunere la noi tehnologii
În urmă cu un deceniu și jumătate, stația de 330 kV în care am lucrat a primit echipamente noi care înregistrează și prelucrează informații despre semnalele electrice dintr-o rețea de un număr foarte mare de senzori amplasați în diferite locuri - registratorul Parma.
Acesta este un computer obișnuit cu propriul software, care efectuează sarcini pur electrice.
Ne-au fost încredințate instalarea, racordarea și reglarea acestuia, cu excepția montajului și configurației trunchiurilor de fibră optică. Nu avem experiență cu ei.
Până în acest punct, comunicarea cu acești senzori avea loc prin circuite electrice convenționale, care se numesc secundare. Cu toate acestea, un întreg grup de aceste dispozitive se afla la mare distanță. Proiectul a presupus schimbul de informații cu aceștia prin cablu de fibră optică. L-am așezat noi înșine în interiorul canalului de cablu, iar un reprezentant al producătorului care a venit din Sankt Petersburg a fost implicat în conectare și verificare.
Atunci a devenit clar că este imposibil să lucrezi cu fibra optică fără echipamente specializate și abilități adecvate. Este imposibil să faci ceva cu el cu propriile mâini.
Design cablu fibră optică
Transmiterea informațiilor are loc prin autostrăzi optice, constând din medii separate, combinate într-o structură comună - un cablu de fibră optică.
Principiul de funcționare al mediilor optice
Schimbul de informații are loc datorită trecerii luminii laser din LED-ul încorporat. Transmiterea sa se realizează prin impulsuri ale unui cod binar într-o singură direcție. Prin urmare, au fost create simultan două canale individuale pentru schimbul de informații.
Despre proiectarea cablurilor
Sticla este un material fragil. Poate fi spart cu ușurință, iar fibra optică funcționează folosind fibre de sticlă. Este clar că au nevoie de protecție fiabilă atât împotriva deteriorării mecanice, cât și împotriva pierderii de energie luminoasă.
În acest scop, mediile optice sunt combinate în diferite moduri în module rigide și din acestea este realizat un cablu de fibră optică. Poate fi de diferite modele. Una dintre ele este prezentată în diagramă.
La substația noastră au fost folosite două tipuri de cablu: unul cu diametrul de 6 mm, iar al doilea cu grosimea degetului arătător al mâinii.
Problema acestei tehnologii este descrisă în detaliu în videoclipul GalileoRU „Fibră optică”.
Așezarea fibrei în câmp
Iarna trecută, în apropierea noastră a fost efectuată o pozare mecanizată a unui astfel de cablu direct în pământ.
Lucrarea a fost efectuată de trei, iar pe teren dificil de patru tractoare cuplate într-un tren. Târau un plug de cabluri îngropat la un metru și jumătate în pământ. Pe căruciorul acestui mecanism se află o bobină mare de cablu, care, atunci când este dezrăucită manual de către operator, eliberează cablul prin canalele plugului în șanțul tăiat.
O bandă de semnal foarte vizibilă este plasată automat deasupra fibrei optice de pe stratul de sol. Este imediat umplut cu pământ, iar pe suprafața solului rămâne o urmă de adâncire de ordinul a douăzeci de centimetri sau puțin mai mult.
După ceva timp, toate neregulile au fost nivelate cu un cuțit buldozer al unui tractor ușor cu roți. Vara, traseul de ouat este acoperit de iarbă. Dar la sol poate fi restaurat prin coloane de beton.
Tehnologia de conectivitate
Pe panoul de pe alee am văzut un mesaj de la Beltelecom care m-a interesat.
De asemenea, a fost amplasat pe toate clădirile adiacente. Într-un mod atât de original, furnizorul a raportat că era folosirii cablurilor telefonice din cupru în zona noastră se sfârșise, iar centralele telefonice automate din apropiere aveau să înceteze în curând să funcționeze.
Toți utilizatorii de telefon fix trebuie să aleagă:
- de acord cu trecerea la echipamente noi oferite de furnizor;
- sau refuză, rămânând pe vechiul cablu de cupru.
Alegerea este voluntară, dar foarte curând centrala telefonică automată va fi oprită: comunicarea telefonică prin cablu de cupru va fi automat întreruptă la Internet. Va trebui să încheiați un contract repetat și să plătiți bani pentru acest serviciu. Furnizorul realizează acum înlocuirea echipamentelor vechi și instalarea unuia nou pe cheltuiala sa, iar toate acestea sunt oferite clienților în mod gratuit.
Îmi dau seama imediat că nu am fost mulțumit. Am fost interesat de internet nelimitat la un tarif favorabil de la furnizor.
Prin urmare, am convenit cu furnizorul să conectez internetul prin fibră optică.
Lucrările efectuate s-au desfășurat în trei etape:
- Instalarea unei rețele de fibră optică;
- Obținerea unui modem nou și instalarea acestuia;
- Crearea și conectarea echipamentelor de rețea de acasă la Internet prin fibră optică.
Lucrari de instalare
Literal, la câteva zile după postarea reclamelor, în casă au apărut echipe de instalatori. Voietul de la ei nu s-a oprit timp de două zile. Structura de panouri a clădirii cu cinci etaje are o acustică bună: sunetele se răspândesc în toate direcțiile.
Lucrarea s-a desfășurat simultan la intrări și apartamente.
Instalarea echipamentelor la intrare
Două echipe separate au lucrat în interiorul casei.
Prima zi
Electricienii au făcut găuri mici prin tavanele dintre podea, au fixat recipiente de plastic și au pus în ele un cablu de fibră optică de 6 mm.
Până la sfârșitul zilei, atârna în inele încolăcite peste fiecare ușă.
Capătul fiecăruia a fost închis cu un dop special.
Zilele următoare
La mijlocul palierului de-a lungul peretelui, au fost perforate găuri în plăci de beton pentru țevi de plastic cu diametrul de 4 cm.
Aceasta este perioada cea mai tare de lucru. Dacă zgomotul primei zile poate fi suportat în mod satisfăcător în timp ce vă aflați în apartament, atunci în această etapă este mai bine să vă mutați și să petreceți timp în alt loc până seara.
Procesul se încheie cu instalarea echipamentelor pentru cutiile de joncțiune optică și țevi din plastic pentru cablurile de fibră optică.
Pentru a alimenta puternicul perforator, electricienii au folosit o bobină de prelungire și au conectat-o la priza de interfon prin deschiderea cutiei de acces comună.
Tragând cablul de alimentare al electromagneților ușii, aceștia au creat acces neautorizat pentru orice persoană la intrare. Conectați prelungitorul la această priză.
Care erau în aer și ce era împrăștiat prin intrarea nu le voi descrie. Restabilirea ordinii normale a durat mai mult de o zi.
Instalarea echipamentelor in apartament
În paralel cu lucrările de la intrare, specialistul furnizorului a încheiat o înțelegere cu clienții, a explicat cerințele de siguranță pentru manipularea fibrei optice fragile și a ajutat cu sfaturi în alegerea locației pentru instalarea unei prize optice.
Poate fi instalat oriunde. Am ales colțul coridorului de lângă interfon și cel vechi. Înălțimea modemului la nivelul genunchiului era destul de potrivită.
Lungimea cablului de fibră optică din apartament era de doar câteva zeci de centimetri. Orificiul a fost perforat cu un perforator la nivelul plintei.
O bucată de sârmă de oțel a fost împinsă prin ea din lateralul intrării.
Pe reversul, capătul cablului de fibră optică a fost lipit.
Din acest loc au fost fixate cutii de plastic.
Am instalat carcasa prizei optice pe perete.
Au așezat fibra optică, făcând un mic golf în caneluri speciale.
Cutiile erau închise cu capace.
Finalizarea acestor lucrări a fost consemnată în documentația maestrului electrician și certificată prin semnătura mea.
O cerință importantă la locul de instalare a modemului este prezența unei prize electrice lângă acesta pentru conectarea sursei de alimentare. Cablul său relativ scurt este limitat la un metru.
A trebuit să fac o muncă suplimentară special pentru modem. : lângă soclu. Locația din colț limitează accesul accidental la acesta.
Obținerea unui modem și pregătirea trecerii la fibră optică
Câteva zile mai târziu, am primit în căsuța mea poștală o notificare de la furnizor cu o propunere de a veni la centrul de servicii pentru a documenta noul contract.
Chestiuni organizatorice
Când am venit la centrul de service, nu era nici o mulțime de clienți și nici coadă. Data și ora indicată de sosire au îndeplinit așteptările mele.
Operatorul furnizorului și-a încheiat rapid munca și am primit documentația completată și o cutie cu modem.
Am fost surprins că atunci când am primit ultima dată modemul ADSL și accesoriile corespunzătoare pentru acesta, toate echipamentele au fost împachetate într-o pungă de plastic de marcă cu reclama companiei. Acum această cutie trebuia să fie ascunsă sub braț: furnizorul a economisit pe ambalaj.
Operatorul a explicat că de la acesta va sosi o echipă de electricieni pentru a instala modemul și a pune o rețea cu fir. Lucrarea se va desfășura în succesiune. Ea a inclus formularul completat pentru păstrarea lui în cutie. Sunt obligat să confirm momentul finalizării instalației cu semnăturile mele și trebuie să transfer documentul completat către comandant.
Apoi va urma următoarea etapă: un specialist în centru de service va sosi să-mi conecteze echipamentul la Internet prin fibră optică. Sarcina lui este să elimine rețeaua telefonică modemul ADSL, splitter-ul și cablurile suplimentare.
În calitate de client al furnizorului, sunt obligat să returnez echipamentul scos la centrul de service în ziua trecerii la fibră optică sau, în cazuri extreme, a doua zi.
Măsuri tehnice
La câteva zile după ce am vizitat centrul de service, doi electricieni au ajuns la apartamentul meu. Le-am dat un modem cu fibră optică pe care să-l monteze pe perete.
Instalarea sa a fost realizată rapid: două găuri au fost perforate cu un perforator și carcasa a fost fixată cu șuruburi autofiletante prin dibluri, a fost introdus un modem în ea și a fost conectat un cablu de fibră optică.
Apartamentul are plinte din plastic in jurul perimetrului etajului. În interiorul lor, două fire răsucite de la modem la telefon și televizor au fost așezate în secret. Eram îngrijorat de lungimea lor: am presupus că se limitează la dimensiuni standard.
Dar problema a fost rezolvată foarte simplu. Instalatorii au un compartiment mare al unui astfel de cablu. Au tăiat piesa necesară, o stivuiesc și apoi o termină pe toate părțile.
Sertizarea urechilor cu conectorii RJ-45 ai cablului set-top box-ului TV interactiv si RJ-11 pentru telefon s-a realizat cu un cleste REXANT.
După finalizarea acestor operațiuni, am semnat ținuta și i-am dat-o maestrului electrician.
Crearea și configurarea Internetului
Schema de intrare
De fapt, a fost asamblată o rețea pentru conectarea unui modem cu fibră optică la Internet. Rămâne să comutați din nou controlul telefonului, al televizorului și al computerului, să aplicați sursa de alimentare și să efectuați reglarea tuturor dispozitivelor.
Această schemă este foarte asemănătoare cu lucrul printr-un cablu telefonic de cupru. Diferența este că aici telefonul fix se conectează după modem și își pierde autonomia atunci când este oprit.
Dacă tensiunea de alimentare a rețelei de uz casnic de 220 de volți dispare, atunci orice modem este întotdeauna oprit. Atunci când funcționează folosind tehnologia ADSL, telefonul cu linia PBX rămâne conectat printr-un splitter, iar conexiunea dispozitivelor vechi fără alimentare separată nu se pierde. Abonatul poate suna oriunde, inclusiv serviciile de urgență pentru a-și rezolva problemele.
În schema de conectare la Internet prin fibră optică, această posibilitate nu este disponibilă. Există doar speranță pentru comunicațiile mobile.
Lucrări de ajustare
După finalizarea tuturor operațiunilor, electricienii au fost nevoiți să conecteze echipamentul cu fibră optică, să configureze computerul, rețeaua Wi-Fi, telefonul, televizorul în funcție de caracteristicile acestuia. Aceste întrebări au fost tratate de specialiștii furnizorului, care au ajuns după trei zile de așteptare.
Unul dintre ei a alimentat modemul cu fibră optică, a scos un laptop și a început să-l configureze.
A introdus datele necesare pentru a conecta telefonul la noua rețea.
Setarea parolei pentru rețeaua Wi-Fi și pentru toate echipamentele este efectuată de specialistul furnizorului. Acest lucru este diferit de conectarea la Internet printr-o linie telefonică prin cablu, unde un utilizator obișnuit poate introduce setările modemului printr-un cablu de corecție și poate schimba parolele la discreția sa.
Cu toate acestea, un utilizator avansat are posibilitatea de a modifica setările modemului cu fibră optică conectându-se la router la 192.168.100.1 prin login și parola din fabrică, pe care furnizorul nu le modifică.
În acest timp, al doilea muncitor a demontat circuitul de alimentare al modemului ADSL, a comutat cablurile de comandă ale televizorului și telefonului la fibră optică. De asemenea, a strâns toate echipamentele vechi care fac obiectul livrării.
Am verificat viteza internetului pe computer.
Am fost avertizat încă o dată că trebuie să merg la centrul de service al furnizorului, să predau echipamentele vechi: modem ADSL, splitter și cabluri, să transfer bani din contul vechi în cel nou.
La trecerea la fibră optică, utilizatorului i se oferă un cont nou pe serviciul furnizorului, iar cel vechi încetează să funcționeze: până la completarea banilor, internetul nu va mai funcționa la el.
Perspectiva de a rămâne fără internet mai mult de o zi nu mi se potrivea. El a întrebat cum poate fi rezolvată această problemă. M-au ajutat să aranjez plata promisă, care trebuie confirmată cu o plată reală în termen de trei zile.
Toate aceste operațiuni au durat aproximativ 10 minute. Le-am mulțumit specialiștilor furnizorului pentru munca depusă și am mers la centrul de service, unde au reușit rapid să rezolve toate problemele și să schimbe planul tarifar cu unul mai profitabil.
Când am venit acasă seara, am constatat că telefonul fix nu mai funcționa. S-a supărat. Era prea târziu să caute specialiști. L-a lăsat pentru a doua zi.
Dimineața, telefonul lucra deja la noul număr, iar viteza internetului a crescut dramatic.
Astfel, a existat o conexiune la Internet prin fibra optică a computerului meu.
Proprietarul videoclipului Diplomatrutube explică în detaliu întrebarea cum „tehnologia PON trece de la centrala telefonică la apartament”.
Dacă aveți întrebări pe această temă, întrebați-le în comentarii.
Atunci când stabiliți comunicații optice, este pur și simplu imposibil să faceți fără conexiuni, deoarece la instalarea liniei principale, lungimea cablului nu este întotdeauna suficientă, iar atunci când aranjați o rețea de cartier sau de casă, devine necesară ramificarea unui cablu mare în mai multe cei mici.
Până în prezent, trei metode de conectare a fibrei optice sunt utilizate pe scară largă:
- cale mecanică;
- conexiune de îmbinare;
- sudarea cablului optic.
Metoda mecanică de conectare a unei fibre optice este un concept ambiguu și nu înseamnă deloc că întreaga procedură este efectuată fără participarea unui echipament de înaltă precizie. În acest caz, nu puteți face fără sudare. Și acest lucru se face în felul următor:
- un conector de fibră mecanică (pigtail), care este o bucată mică de fibră optică cu un conector instalat din fabrică, este sudat de cablu folosind un splicer automat;
- în plus, ramurile sudate trebuie conectate la echipamentul echipat cu conectorul necesar pentru aceasta.
Această metodă de conectare necesită întreținere constantă, deoarece conectorii se murdăresc periodic și trebuie curățați. De asemenea, merită remarcat faptul că nivelul de pierdere a semnalului este foarte mare, ceea ce este complet inacceptabil atunci când se instalează autostrăzi externe.
Conexiune de îmbinare. O modalitate cu adevărat manuală de îmbinare a capetelor pregătite ale unui cablu de fibră optică, care necesită un meșter cu înaltă calificare care execută lucrarea, instrumentul minim necesar este realizat fără sudură. Întregul proces de instalare este mult mai ușor și mai rapid. Și se realizează după cum urmează:
- conform standardelor, două capete ale fibrei sunt prelucrate;
- după aceea, prin ghidaje speciale, acestea sunt reunite în direcția îmbinării în sine și fixate;
- în continuare, urmează procesul de refacere a mantalei de protecție și a armăturii cablului.
Pentru a minimiza pierderea semnalului, cavitatea de îmbinare este umplută cu un gel special (deseori este deja în conector). În comparație cu metoda mecanică, îmbinarea fibrelor arată mai puțină atenuare în cablul optic. Cu toate acestea, adesea, acest coeficient poate fi egal cu 0,1 dB. În același timp, merită să acordați o atenție deosebită faptului că nivelul pierderilor în acest tip de conexiune poate crește în timp, ceea ce va necesita o ajustare suplimentară a poziției capetelor îmbinate unul în raport cu celălalt. Acest lucru este cauzat de deplasarea cablului în timpul funcționării sau de uscarea gelului.
Al treilea și cel mai fiabil mod de a conecta un cablu de fibră optică este sudarea. Această opțiune de îmbinare a capetelor este cea mai durabilă. Chiar și cu un proces de lucru mai lung, spre deosebire de un conector de fibră mecanică sau de îmbinare, acesta prezintă rezultate excelente asociate cu reducerea la minimum a pierderii nivelului de semnal la 0,04 dB, ceea ce are un efect pozitiv asupra calității semnalului. Procesul în sine implică executarea secvențială a unui număr de operațiuni legate de pregătirea, îmbinarea directă a capetelor fibrei și este demn de un articol separat.
xn----etbqnigrhw.xn--p1ai
Cum se conectează cablul de fibră optică
Vei avea nevoie
- - îmbinare;
- - servetel fara scame;
- - alcool;
- - satar;
- - aparat special de sudura;
- - tester optic.
Instruire
Pentru o conexiune mecanică, veți avea nevoie de o îmbinare, în corpul căruia capetele despicate ale fibrelor optice sunt introduse prin canale. În primul rând, acestea trebuie curățate și degresate. Îndepărtați carcasa cu un strat tampon. Umeziți o cârpă fără scame cu alcool și degresați capetele fibrelor cu ea. Apoi despicați capătul fibrei la un unghi de 90° folosind o unealtă specială - un saiar.
Introduceți capetele finite prin canalele laterale ale îmbinării din diferite părți în camera, care este umplută cu gel de imersie. Introduceți fibrele până la contactul reciproc. Capacul de îmbinare, după închidere, va fixa în siguranță joncțiunea. Instalați îmbinarea asamblată pe placa de îmbinare a crucii sau a manșonului împreună cu furnizarea tehnologică de fibră. Verificați calitatea conexiunii cu un reflectometru sau un tester optic.
O altă metodă de îmbinare a fibrelor optice este sudarea. Pentru aceasta, veți avea nevoie de un aparat special care conține un microscop, cleme, sudare cu arc, un microprocesor și o cameră termocontractabilă. Pregătiți capetele fibrelor pentru îmbinare în același mod în care le-ați pregătit pentru îmbinare mecanică prin îndepărtarea tecii de pe ele. Puneți un manșon termocontractabil la un capăt pentru a proteja sudurile. Apoi, așa cum este indicat în primul pas, degresați și ciobiți capetele.
Așezați fibrele în dispozitivul de îmbinare în care se vor alinia. Dispozitivul automat va alinia fibrele, va evalua cipul și, după ce a primit confirmarea de la operator, va suda. Dacă mașina nu are aceste funcții, aceste operațiuni trebuie efectuate manual. Evaluați calitatea sudurii cu un reflectometru optic. Acest dispozitiv vă va permite să identificați gradul de atenuare și eterogenitate. Glisați manșonul de protecție în locul pentru a fi sudat și puneți-l în cuptorul termocontractabil pentru un minut. Când manșonul s-a răcit, așezați-l în placa de îmbinare de protecție a crucii sau a manșonului, împreună cu alimentarea tehnologică cu fibră.
www.kakprosto.ru
Metode de conectare a fibrelor optice
Pentru a combina rețelele situate în clădiri diferite într-un singur spațiu de informații, nu se poate face fără a construi linii de cablu trunchi. În funcție de rata de transfer de date sau semnal necesară, distanțele dintre porturile echipamentelor active, diverse tehnologii și medii de transmisie a datelor pot fi utilizate pentru coloana vertebrală: cabluri coaxiale, cabluri torsadate, cabluri optice și tehnologii fără fir.
Din punct de vedere funcțional, atunci când distanțele dintre rețele sunt de peste 150 de metri, și când este necesar să se transfere date de peste 10 Mbps, cea mai bună variantă astăzi este utilizarea cablurilor optice și construirea liniilor de comunicație prin fibră optică (FOCL). Mediul de transmisie a datelor în FOCL este o fibră optică (fibră).
Orez. 1 Structura fibrei
Proiectarea fibrei optice este prezentată schematic în Figura 1, a și b - miezul și placarea fibrei optice; c, d și e - cochilii tampon, de întărire și de protecție. Atunci când se construiește o coloană vertebrală în SCS, standardele permit utilizarea a două tipuri de fibre optice: fibră monomod și multimod.
Avantajele utilizării cablurilor optice sunt evidente, acestea fiind o lățime de bandă largă, limitată în prezent doar de capacitățile echipamentului terminal, un nivel scăzut de atenuare care permite utilizarea unei linii de comunicație la o distanță de câteva zeci de kilometri fără amplificarea semnalului optic, securitate bună a informațiilor care nu pot fi citite de pe linie fără a-i încălca integritatea și multe altele. Dar FOCL are și dezavantaje, dintre care unul este o anumită dificultate în conectarea secțiunilor individuale ale cablului. Iar una dintre cele mai importante lucrări după pozarea cablului, care necesită prezența specialiștilor de înaltă calificare în companie, este conectarea fibrelor optice.
Astăzi, există multe tehnologii pentru conectarea fibrelor optice. În acest articol, voi lua în considerare două dintre ele - aceasta este sudarea cu arc, realizată folosind o mașină de sudură și o conexiune mecanică în interiorul unui manșon special - o îmbinare (nu confundați cu un manșon de cablu folosit pentru a conecta două sau mai multe cabluri optice).
Îmbinarea fibrelor optice
Pentru sudarea fibrelor optice se folosește un aparat special de sudură. Acesta este un dispozitiv complex care conține un microscop folosit pentru alinierea fibrelor, cleme cu caneluri în formă de V pentru fixarea fiabilă a fibrelor și microdrive utilizate pentru automatizarea procesului, sudarea cu arc, o cameră termocontractabilă pentru încălzirea manșoanelor de protecție, un microprocesor utilizat. pentru a controla dispozitivul și un control al calității sistemului.
Tehnologia procesului de sudare a fibrei optice constă din următorii pași:
- Scoaterea cochiliilor prezentate în fig. 1 c-d folosind un strat tampon - un instrument conceput pentru a lucra cu fibre de diferite diametre.
- Pregătirea fibrei pentru sudare. Mai întâi, la unul dintre capete se pune un manșon termocontractabil, care este necesar pentru a proteja locul de sudare. Apoi capetele decupate ale fibrelor sunt degresate cu o cârpă fără scame înmuiată în alcool. După degresare, capătul fibrei este desprins cu un dispozitiv special - un saiar. Unghiul de scindare ar trebui să fie de 90°±1,5°, în caz contrar, se va forma neomogenitate la locul de sudare, ceea ce duce la atenuări mari și reflexii înapoi. După clivaj, fibrele optice sunt plasate în aparatul de sudură.
- Sudare. În primul rând, fibrele din mașină sunt aliniate. Dacă dispozitivul este automat, atunci el însuși estimează unghiul de clivaj, ajustează fibrele unul față de celălalt și, după confirmarea de către operator, conduce procesul de sudare. Dacă dispozitivul nu este automat, atunci toate aceste operațiuni sunt efectuate manual de către un specialist. În timpul procesului de sudare, fibrele sunt încălzite și topite printr-un arc electric, apoi combinate, iar locul de sudare este încălzit suplimentar pentru a elimina tensiunile interne.
- Controlul calității sudurii. Aparatul automat de sudură analizează imaginile primite de la microscop și oferă o estimare aproximativă a nivelului de pierdere. Mai precis, rezultatul poate fi evaluat folosind un reflectometru optic - un dispozitiv care vă permite să identificați neomogenitățile și gradul de atenuare pe întreaga linie.
- Protecția locului de sudare. Manșonul de protecție, îmbrăcat la un capăt al cablului, este deplasat la locul sudării și introdus într-un cuptor termocontractabil pentru aproximativ un minut. După răcire, manșonul este plasat în placa de îmbinare de protecție a cuplajului sau cadrului de distribuție optică, unde este plasat stocul tehnologic al fibrei.
Conexiunea mecanică a fibrelor optice - îmbinare mecanică
Pentru conectarea mecanică a fibrelor optice, se folosește un dispozitiv special - o îmbinare, al cărui design schematic este prezentat în Figura 2.
Orez. 2 Design de îmbinare pentru îmbinarea mecanică a fibrelor optice
Lipirea constă dintr-un corp (a), în care, prin canale și ghidaje speciale, sunt introduse capetele ciobite ale fibrelor (d). Ghidajele sunt utilizate pentru îmbinarea cu precizie a capetelor într-o cameră umplută cu gel de imersie (e), care este necesar pentru a minimiza atenuarea diafoniei și etanșeitatea conexiunii. Indicele de refracție al gelului este apropiat de cel al miezului fibrei, minimizând reflexia din spate. De sus carcasa este închisă de un capac (b).
Tehnologia procesului de conectare a fibrelor optice folosind o îmbinare mecanică constă în următorii pași:
1. și 2. Similar cu punctele 1 și 2 când se utilizează îmbinarea fibrelor. Capetele fibrelor sunt curățate, degresate și capetele lor sunt ciobite. Toleranțele unghiului de clivaj sunt, de asemenea, foarte strânse. Diferența dintre o îmbinare mecanică și o îmbinare sudată este că nu este necesară utilizarea unui manșon termocontractabil, deoarece îmbinarea mecanică îndeplinește funcția de protecție mecanică a fibrelor optice.
3. Conexiune mecanică. Capetele pregătite ale fibrelor sunt introduse din diferite părți prin canalele laterale ale îmbinării într-o cameră umplută cu gel de imersie. Fibrele sunt introduse înainte de contactul reciproc. După introducere, capacul de îmbinare se închide și fixează ferm joncțiunea.
4. Pozare. Lipirea asamblată este instalată pe placa de îmbinare a cuplajului sau crucii, odată cu aceasta se plasează și sursa tehnologică de fibră.
Calitatea conexiunii mecanice poate fi verificată cu un tester optic sau reflectometru.
Comparație între utilizarea îmbinării sau îmbinării mecanice a fibrelor optice
Fiecare dintre cele două metode prezentate are propriile sale avantaje și dezavantaje.
Avantajele unei îmbinări sudate includ diafonia redusă, fiabilitatea ridicată și viteza mare de îmbinare a fibrelor. Dezavantajul este costul ridicat al echipamentului (mașină de sudură), prezența unui operator calificat, necesitatea unei suprafețe mai mari pentru efectuarea lucrărilor și alimentarea (sau reîncărcarea) aparatului de sudură.
Avantajele unei conexiuni mecanice sunt simplitatea și timpul redus de instalare, o lungime mai mică a marjei tehnologice a fibrei, iar dezavantajele sunt un nivel mai ridicat de atenuare a diafoniei.
Aplicarea metodelor de aplicare descrise în articol
Este logic să folosiți îmbinări sudate atunci când construiți secțiuni lungi de autostrăzi. În cazurile care necesită o calitate înaltă a liniei, de exemplu, când se construiesc linii de fibră optică de mare viteză pentru centrele de date, unde sunt necesari parametri de atenuare scăzută și reflexie din spate.
Îmbinarea folosind o îmbinare mecanică este folosită cel mai adesea pentru conexiuni temporare, de exemplu, pentru repararea urgentă a deteriorării cablurilor, pentru instalarea de linii cu costuri reduse și atunci când se lucrează în locuri greu accesibile.
www.leksa.net
Cum se sertează fibra
Vei avea nevoie
- - un set specializat de instrumente;
- - tăietor cuțit;
- - freze laterale (de preferat ceramice).
Instruire
Sertizarea fibrei optice începe cu tăierea cablului. Îndepărtarea stratului superior și a armurii nu este practic diferită de lucrul cu un omologul din cupru. Singurul lucru de reținut este că îndoirile și îndoirile puternice ale cablului nu ar trebui permise, deoarece fibra este foarte fragilă în structura sa.
După îndepărtarea primelor două capace de protecție, lucrarea trebuie făcută cu mai multă grijă pentru a nu deteriora firele de fibră optică. Încercați să faceți o tăietură longitudinală superficială cu un tăietor fără a încălca integritatea împletiturii de polietilenă. Acum îndepărtați stratul de polimer și desfășurați banda de protecție.
Următoarea etapă de lucru poate fi efectuată numai folosind un set specializat de instrumente. Cumpărând un astfel de kit, nu ar trebui să fii ieftin, deoarece rezultatul final, de regulă, depinde de calitatea produselor pe care le folosești.
A efectua iluminarea în orice baie, în special într-o baie de aburi, nu este o sarcină ușoară, deoarece în astfel de încăperi mediul cel mai nefavorabil pentru inginerie electrică: temperatură ridicată, umiditate constantă, vaporizare. În special pentru băi, au fost dezvoltate modele de lămpi cu fibră optică, care fac posibil să se facă fără cabluri electrice în camera de aburi.
În acest articol:
Caracteristicile de proiectare ale dispozitivelor de iluminat cu fibră optică
Pentru astfel de echipamente de iluminat, capacitatea sticlei de a furniza un flux luminos pe distanțe destul de mari este utilizată practic fără pierderi. De regulă, firele lungi sunt făcute din sticlă, care se numesc fibre. Apoi sunt colectate într-un singur pachet, învelite (sau nu) într-o teacă de protecție specială.
Opinia expertului
Ivan Zaitsev
Specialist în iluminat, consultant în departamentul materiale de construcție al unui mare lanț de retail
Întrebați un expertPentru informația dumneavoastră! Dacă fibra de sticlă este omogenă, fără defecte, raza sa de transmisie a luminii poate fi de kilometri. Desigur, producția unor astfel de conductori, spre deosebire de candelabrele convenționale de tavan, este destul de costisitoare, astfel încât utilizarea dispozitivelor de iluminat cu fibră optică în viața de zi cu zi este limitată.
Dar dezvoltatorii au găsit o modalitate de a reduce costul tehnologiei de producție a fibrei optice. Pentru aceasta, a fost folosit un material polimeric - acrilic. Un astfel de conductor optic nu este, de asemenea, ieftin, dar costă de câteva ori mai puțin decât sticla.
Principiul de funcționare
Cum funcționează sistemele de iluminat ale acestui design? De regulă, un emițător de proiector echipat cu elemente speciale de filtrare este fixat la un capăt al cablului de fibră optică. Ca rezultat, transmisia luminii este realizată de firele de fibră optică pe o parte opusă firelor de fibră optică. Vizual, razele de lumină pot fi observate pe secțiuni de fire de fibră optică. Pentru a oferi o formă diferită strălucirii, pe fiecare astfel de fir se pun lentile mici care împrăștie lumina emisă.
Intensitatea luminii va depinde de următorii factori:
Pentru informația dumneavoastră! Sunt fabricate fibre, ai căror pereți strălucesc și (dacă nu există izolație).
Compoziția sistemului
Lămpile cu fibră optică sunt vândute cel mai adesea în kituri, care includ următoarele componente:
- Proiector. Aceasta este o instalație specială de dimensiuni mici - singurul element structural care este conectat la o sursă de alimentare. Proiectorul folosește lămpi cu descărcare în gaz, halogen, LED. În plus, puteți utiliza: un declanșator, un convertor de tensiune, mai multe lentile diferite pentru schimbarea culorilor și alte părți. Nivelul de iluminare al camerei va depinde de numărul de elemente suplimentare, de puterea sursei de lumină.
- Fire optice - fibre. Ele creează un flux luminos direcționat (în manta), de asemenea, sunt capabile să formeze o strălucire de tip liniar pe toată lungimea firului de fibră optică. Există opțiuni pentru strălucirea punctuală de-a lungul firului de fibră optică. Luminozitatea fluxului luminos depinde în primul rând de diametrul firului de fibră optică, de puterea echipamentului de iluminat, în acest caz un proiector cu lămpi.
Pentru informația dumneavoastră! Numărul de fibre poate fi calculat în unități și mii de fire de fibră optică. Iluminarea băii de aburi se realizează tocmai printr-o combinație de fire cu diferite caracteristici.
Pentru informația dumneavoastră! Există, de asemenea, o varietate de părți rotative, mobile, mecanisme de reglare a intensității fluxului de lumină, care pot fi instalate suplimentar pe dispozitivele de iluminat. .
Când plănuiți să organizați iluminarea cu fibră optică a unei băi de țară cu propriile mâini, se recomandă să selectați echipamente de iluminat din această categorie nu numai în ceea ce privește numărul și lungimea fibrelor. Este necesar să se acorde atenție sursei de lumină utilizată - GL, GRL, LED.
Dacă în reflector există lămpi cu descărcare în gaz, cu halogen, este necesar să verificați funcționarea ventilatorului de răcire. Sunt modele destul de zgomotoase care pot strica restul. De aceea, este recomandat sa achizitionati proiectoare cu elemente led care nu se incalzesc deloc, deci nu necesita racire.