Përforcuesit qëllimi kryesor i të cilëve është përforcimi i sinjalit me fuqi quhen amplifikatorë të fuqisë. Si rregull, amplifikatorë të tillë drejtojnë një ngarkesë me rezistencë të ulët, siç është një altoparlant.
3-18 V (nominale - 6 V). Konsumi maksimal i rrymës është 1,5 A me një rrymë qetësuese prej 7 mA (në 6 V) dhe 12 mA (në 18 V). Fitimi i tensionit 36.5 dB. në -1 dB 20 Hz - 300 kHz. Fuqia e vlerësuar e daljes në 10% THD
fikni përkohësisht tingullin. Mund të dyfishoni fuqinë dalëse të TDA7233D kur i ndizni sipas qarkut të paraqitur në Fig. 31.42. C7 parandalon vetë-ngacmimin e pajisjes në zonë
frekuencave të larta. R3 zgjidhet derisa të merret një amplitudë e barabartë e sinjaleve të daljes në daljet e mikroqarqeve.
Oriz. 31.43. KR174UNZ 7
KR174UN31 është menduar për përdorim si pajisje elektronike shtëpiake me fuqi të ulët dalëse.
Kur tensioni i furnizimit ndryshon nga
2.1 deri në 6.6 V me një konsum mesatar aktual prej 7 mA (pa sinjalin e hyrjes), fitimi i tensionit të mikroqarkut varion nga 18 në 24 dB.
Koeficienti i shtrembërimit jolinear në një fuqi dalëse deri në 100 mW nuk është më shumë se 0,015%, voltazhi i zhurmës së daljes nuk kalon 100 μV. Hyrja e mikroqarkut është 35-50 kOhm. ngarkesa - jo më e ulët se 8 Ohms. Gama e frekuencës së funksionimit - 20 Hz - 30 kHz, kufiri - 10 Hz - 100 kHz. Tensioni maksimal i sinjalit të hyrjes është deri në 0,25-0,5 V.
Artikulli u kushtohet dashamirëve të muzikës me zë të lartë dhe me cilësi të lartë. TDA7294 (TDA7293) është një mikroqark përforcues me frekuencë të ulët i prodhuar nga kompania franceze THOMSON. Qarku përmban transistorë me efekt në terren, i cili siguron cilësi të lartë të zërit dhe zë të butë. Një qark i thjeshtë me pak elementë shtesë e bën qarkun të aksesueshëm për çdo radio amator. Një përforcues i montuar saktë nga pjesët e shërbimit fillon të funksionojë menjëherë dhe nuk kërkon rregullim.
Përforcuesi i fuqisë audio në çipin TDA 7294 ndryshon nga amplifikuesit e tjerë të kësaj klase:
- fuqi e lartë e prodhimit,
- Gama e gjerë e tensionit të furnizimit,
- përqindje e ulët e shtrembërimit harmonik,
- "tingull i butë,
- disa pjesë "të bashkangjitura",
- çmim i ulët.
Mund të përdoret në pajisjet audio radio amatore, kur modifikoni amplifikatorët, sistemet e altoparlantëve, pajisjet audio, etj.
Fotografia më poshtë tregon diagrami tipik i qarkut përforcues fuqie për një kanal.
Mikroqarku TDA7294 është një përforcues i fuqishëm operacional, fitimi i të cilit vendoset nga një qark reagimi negativ i lidhur midis daljes së tij (pina 14 e mikroqarkut) dhe hyrjes së përmbysjes (pina 2 e mikroqarkut). Sinjali i drejtpërdrejtë furnizohet në hyrje (pin 3 e mikroqarkut). Qarku përbëhet nga rezistorët R1 dhe kondensatori C1. Duke ndryshuar vlerat e rezistencës R1, mund të rregulloni ndjeshmërinë e amplifikatorit në parametrat e para-amplifikuesit.
Diagrami i bllokut të amplifikatorit në TDA 7294
Karakteristikat teknike të çipit TDA7294
Karakteristikat teknike të çipit TDA7293
Diagrami skematik i amplifikatorit në TDA7294
Për të montuar këtë përforcues do t'ju nevojiten pjesët e mëposhtme:
1. Çipi TDA7294 (ose TDA7293)
2. Rezistenca me fuqi 0,25 vat
R1 - 680 Ohm
R2, R3, R4 - 22 kOm
R5 - 10 kOhm
R6 - 47 kOhm
R7 - 15 kOhm
3. Kondensator filmi, polipropileni:
C1 – 0,74 mkF
4. Kondensatorët elektrolitikë:
C2, C3, C4 – 22 mkF 50 volt
C5 – 47 mkF 50 volt
5. Rezistencë e dyfishtë e ndryshueshme - 50 kOm
Një përforcues mono mund të montohet në një çip. Për të montuar një përforcues stereo, duhet të bëni dy dërrasa. Për ta bërë këtë, ne i shumëzojmë të gjitha pjesët e nevojshme me dy, përveç rezistencës së dyfishtë të ndryshueshme dhe furnizimit me energji elektrike. Por më shumë për këtë më vonë.
Pllaka e qarkut përforcues bazuar në çipin TDA 7294
Elementet e qarkut janë montuar në një tabelë qark të printuar të bërë nga tekstil me fije qelqi me fletë të njëanshme.
Një qark i ngjashëm, por me disa elementë më shumë, kryesisht kondensatorë. Qarku i vonesës së ndezjes në hyrjen e pinit 10 "me zë" është aktivizuar. Kjo është bërë për një ndezje të butë dhe pa zhurmë të amplifikatorit.
Në tabelë është instaluar një mikroqark, nga i cili janë hequr kunjat e papërdorura: 5, 11 dhe 12. Instaloni duke përdorur një tel me një seksion kryq prej të paktën 0,74 mm2. Vetë çipi duhet të instalohet në një radiator me një sipërfaqe prej të paktën 600 cm2. Radiatori nuk duhet të prekë trupin e amplifikatorit në mënyrë të tillë pasi do të ketë një tension negativ të furnizimit në të. Vetë strehimi duhet të lidhet me një tel të përbashkët.
Nëse përdorni një zonë më të vogël të radiatorit, duhet të bëni rrjedhje të detyruar të ajrit duke vendosur një tifoz në kutinë e amplifikatorit. Tifoz është i përshtatshëm nga një kompjuter me një tension prej 12 volt. Vetë mikroqarku duhet të lidhet me radiatorin duke përdorur paste përçuese të nxehtësisë. Mos e lidhni radiatorin me pjesët e ndezura, përveç autobusit të energjisë negative. Siç u përmend më lart, pllaka metalike në pjesën e pasme të mikroqarkut është e lidhur me qarkun e energjisë negative.
Çipat për të dy kanalet mund të instalohen në një radiator të përbashkët.
Furnizimi me energji elektrike për amplifikatorin.
Furnizimi me energji elektrike është një transformator në rënie me dy dredha-dredha me një tension prej 25 volt dhe një rrymë prej të paktën 5 amper. Tensioni në mbështjellje duhet të jetë i njëjtë dhe po ashtu edhe kondensatorët e filtrit. Mosbalancimi i tensionit nuk duhet të lejohet. Kur furnizoni amplifikatorin me energji bipolare, ai duhet të furnizohet njëkohësisht!
Është më mirë të instaloni dioda ultra të shpejta në ndreqës, por në parim, ato të zakonshme si D242-246 me një rrymë prej të paktën 10A janë gjithashtu të përshtatshme. Këshillohet që të lidhni një kondensator me kapacitet 0.01 μF paralelisht me secilën diodë. Ju gjithashtu mund të përdorni ura diodë të gatshme me të njëjtat parametra aktualë.
Kondensatorët e filtrit C1 dhe C3 kanë një kapacitet prej 22,000 mikrofaradësh në një tension prej 50 volt, kondensatorët C2 dhe C4 kanë një kapacitet prej 0,1 mikrofarad.
Tensioni i furnizimit prej 35 volt duhet të jetë vetëm me një ngarkesë prej 8 ohms; nëse keni një ngarkesë prej 4 ohms, atëherë tensioni i furnizimit duhet të reduktohet në 27 volt. Në këtë rast, voltazhi në mbështjelljet sekondare të transformatorit duhet të jetë 20 volt.
Ju mund të përdorni dy transformatorë identikë me një fuqi prej 240 watts secili. Njëra prej tyre shërben për të marrë tension pozitiv, e dyta - negative. Fuqia e dy transformatorëve është 480 vat, e cila është mjaft e përshtatshme për një përforcues me fuqi dalëse 2 x 100 vat.
Transformatorët TBS 024 220-24 mund të zëvendësohen me çdo tjetër me një fuqi prej të paktën 200 watts secili. Siç është shkruar më lart, ushqimi duhet të jetë i njëjtë - transformatorët duhet të jenë të njëjtë!!! Tensioni në mbështjelljen dytësore të secilit transformator është nga 24 në 29 volt.
Qarku i amplifikatorit fuqi e rritur në dy çipa TDA7294 në një qark urë.
Sipas kësaj skeme, për versionin stereo do t'ju duhen katër mikroqarqe.
Specifikimet e amplifikatorit:
- Fuqia maksimale e daljes në ngarkesë 8 Ohm (furnizim +/- 25V) - 150 W;
- Fuqia maksimale e daljes në një ngarkesë prej 16 Ohms (furnizimi +/- 35V) - 170 W;
- Rezistenca e ngarkesës: 8 - 16 Ohms;
- Koefi. shtrembërim harmonik, në maksimum. fuqia 150 vat, p.sh. 25V, ngrohje 8 Ohm, frekuenca 1 kHz - 10%;
- Koefi. shtrembërim harmonik, në një fuqi prej 10-100 vat, për shembull. 25V, ngrohje 8 Ohm, frekuenca 1 kHz - 0,01%;
- Koefi. shtrembërim harmonik, për shembull, me një fuqi prej 10-120 watts. 35V, ngrohje 16 Ohm, frekuenca 1 kHz - 0,006%;
- Gama e frekuencës (me një përgjigje jo frekuence prej 1 db) - 50 Hz ... 100 kHz.
Pamje e amplifikatorit të përfunduar në një kuti druri me një mbulesë të sipërme transparente nga pleksiglas.
Që amplifikatori të funksionojë me fuqi të plotë, duhet të aplikoni nivelin e kërkuar të sinjalit në hyrjen e mikroqarkut, dhe kjo është të paktën 750 mV. Nëse sinjali nuk është i mjaftueshëm, atëherë duhet të montoni një para-përforcues për rritje.
Qarku parapërforcues në TDA1524A
Vendosja e amplifikatorit
Një përforcues i montuar siç duhet nuk ka nevojë për rregullim, por askush nuk garanton që të gjitha pjesët janë absolutisht në gjendje të mirë pune; duhet të keni kujdes kur e ndizni për herë të parë.
Ndezja e parë kryhet pa ngarkesë dhe me burimin e sinjalit të hyrjes të fikur (është më mirë të lidhni hyrjen me një kërcyes). Do të ishte mirë të përfshini siguresat prej rreth 1A në qarkun e energjisë (si në plus ashtu edhe në minus midis burimit të energjisë dhe vetë amplifikatorit). Shkurtimisht (~0,5 sek.) Aplikoni tensionin e furnizimit dhe sigurohuni që rryma e konsumuar nga burimi të jetë e vogël - siguresat nuk digjen. Është i përshtatshëm nëse burimi ka tregues LED - kur shkëputen nga rrjeti, LED-të vazhdojnë të ndizen për të paktën 20 sekonda: kondensatorët e filtrit shkarkohen për një kohë të gjatë nga rryma e vogël qetësuese e mikroqarkut.
Nëse rryma e konsumuar nga mikroqarku është e madhe (më shumë se 300 mA), atëherë mund të ketë shumë arsye: qark i shkurtër në instalim; kontakt i dobët në telin "tokë" nga burimi; "plus" dhe "minus" janë të ngatërruara; kunjat e mikrocirkut prekin kërcyesin; mikroqarku është i gabuar; kondensatorët C11, C13 janë ngjitur gabimisht; kondensatorët C10-C13 janë të gabuar.
Duke u siguruar që gjithçka është normale me rrymën qetësuese, ne e ndezim me siguri energjinë dhe matim tensionin konstant në dalje. Vlera e tij nuk duhet të kalojë +-0,05 V. Tensioni i lartë tregon probleme me C3 (më rrallë me C4), ose me mikroqarkun. Ka pasur raste kur rezistenca "tokë-tokë" ishte ose e bashkuar dobët ose kishte një rezistencë prej 3 kOhms në vend të 3 ohms. Në të njëjtën kohë, prodhimi ishte konstant 10 ... 20 volt. Duke lidhur një voltmetër AC në dalje, sigurohemi që voltazhi AC në dalje të jetë zero (kjo bëhet më së miri me hyrjen të mbyllur, ose thjesht me kabllon hyrëse të pa lidhur, përndryshe do të ketë zhurmë në dalje). Prania e tensionit të alternuar në dalje tregon probleme me mikroqarkun, ose qarqet C7R9, C3R3R4, R10. Fatkeqësisht, testuesit konvencionalë shpesh nuk mund të matin tensionin me frekuencë të lartë që shfaqet gjatë vetë-ngacmimit (deri në 100 kHz), kështu që është më mirë të përdorni një oshiloskop këtu.
Nëse keni nevojë të bëni një UMZCH të thjeshtë por mjaft të fuqishëm, mikroqarku TDA2040 ose TDA2050 do të jetë zgjidhja më e mirë dhe e lirë. Ky amplifikues i vogël stereo AF është ndërtuar mbi bazën e dy mikroqarqeve të njohura TDA2030A. Krahasuar me lidhjen klasike, ky qark ka përmirësuar filtrimin e energjisë dhe strukturën e optimizuar të PCB-ve. Pas shtimit të çdo paraampi dhe furnizimi me energji, dizajni është ideal për të bërë një amplifikator të energjisë audio shtëpiake, afërsisht 15 W (çdo kanal). Projekti bazohet në TDA2030A, por ju mund të përdorni TDA2040 ose TDA2050, duke rritur kështu fuqinë e daljes me një herë e gjysmë. Përforcuesi është i përshtatshëm për altoparlantët me një rezistencë prej 8 ose 4 ohms. Avantazhi i dizajnit është se nuk kërkon furnizim me energji bipolare, si shumica. Qarku ka parametra të mirë, lehtësinë e fillimit dhe funksionimin e besueshëm.
Diagrami skematik i ULF
Përforcues 2x15W TDA2030 - qark stereoTDA2030A ju lejon të bashkoni një përforcues të klasës AB me frekuencë të ulët. Mikroqarku siguron një rrymë të madhe dalëse, ndërkohë që karakterizohet nga shtrembërim i ulët i sinjalit. Ekziston një mbrojtje e integruar e qarkut të shkurtër, e cila kufizon automatikisht fuqinë në një vlerë të sigurt, si dhe mbrojtje termike tradicionale për pajisje të tilla. Qarku përbëhet nga dy kanale identike, funksionimi i njërit prej të cilëve përshkruhet më poshtë.
Parimi i funksionimit të amplifikatorit në TDA2030
Rezistorët R1 (100k), R2 (100k) dhe R3 (100k) shërbejnë për të krijuar një zero virtuale për amplifikatorin U1 (TDA2030A), dhe kondensatori C1 (22uF/35V) filtron këtë tension. Kondensatori C2 (2.2 uF/35V) ndërpret komponentin DC - parandalon që tensioni DC të hyjë në hyrjen e mikroqarkut të amplifikatorit përmes hyrjes lineare.
Elementet R4 (4.7k), R5 (100k) dhe C4 (2.2 uF/35V) veprojnë në një lak reagimi negativ dhe kanë për detyrë të formojnë përgjigjen e frekuencës së amplifikatorit. Rezistorët R4 dhe R5 përcaktojnë nivelin e fitimit, ndërsa C4 siguron fitimin e unitetit për komponentin DC.
Rezistenca R6 (1R) së bashku me kondensatorin C6 (100nF) punojnë në një sistem që formon karakteristikën e përgjigjes së frekuencës në dalje. Kondensatori C7 (2200uF/35V) parandalon që rryma DC të kalojë përmes altoparlantit (duke kaluar sinjalin audio AC të muzikës).
Diodat D1 dhe D2 parandalojnë që tensionet e rrezikshme të polaritetit të kundërt të ndodhin në spiralen e altoparlantit dhe të dëmtojnë çipin. Kondensatorët C3 (100nF) dhe C5 (1000uF/35V) filtrojnë tensionin e furnizimit.
Pllaka e qarkut të printuar ULF
Pllaka e qarkut të printuar ULF TDA2030
Ju mund të shihni tabelën e qarkut të printuar në fotografi. me vizatime mund të jetë në arkiv (pa regjistrim). Sa i përket montimit, është e përshtatshme që së pari të bashkoni dy kërcyes në autobusët e energjisë. Nëse është e mundur, duhet të përdorni një tel më të trashë, në vend të një këmbë të hollë rezistence, siç ndodh shpesh. Nëse amplifikatori do të funksionojë me altoparlantë 8 Ohm, dhe jo me 4 Ohm, kondensatorët C7 dhe C14 (2200uF/35V) mund të kenë një vlerë prej 1000uF.
Duhet patjetër të vidhosni radiatorë ose një radiator të zakonshëm në fllanxha, duke kujtuar se kutitë e mikroqarqeve TDA2030A janë të lidhura brenda me tokën.
Ju mund të përdorni me sukses mikroqarqet TDA2040 ose TDA2050 në një tabelë të qarkut të printuar pa ndonjë ndryshim të pikës. Pllaka është projektuar në mënyrë që të mund të pritet nëse është e nevojshme në vendin e treguar nga vija me pika dhe mund të përdoret vetëm gjysma e amplifikatorit me çipin U1. Në vend të lidhësve AR2 (TB2-5) dhe AR3 (TB2-5), mund të lidhni telat drejtpërdrejt nëse lidhësit audio janë të fiksuar në trupin e amplifikatorit.
Pllaka e qarkut të printuar të amplifikatorit gati me rregullimin e pjesëve
Kutia dhe furnizimi me energji elektrike
Merrni një furnizim me energji elektrike ose me një transformator plus një ndreqës, ose një ndërprerës të gatshëm, për shembull nga një laptop. Përforcuesi duhet të fuqizohet me një tension të pastabilizuar brenda intervalit 12 - 30 V. Tensioni maksimal i furnizimit është 35 V, që natyrisht është më mirë të mos arrihet me disa volt, nuk e dini kurrë.
Bërja e një kutie nga e para është shumë e mundimshme, kështu që mënyra më e lehtë është të zgjidhni një kuti të gatshme (metal, plastik) apo edhe një kuti të gatshme nga një pajisje elektronike (akordues TV satelitor, DVD player).
Ata po bëhen një gjë e së kaluarës dhe tani, për të montuar ndonjë përforcues të thjeshtë, nuk duhet të luftoni më me llogaritjet dhe të gozhdoni një tabelë të madhe qarku të printuar.
Tani pothuajse të gjitha pajisjet e lira të amplifikimit bëhen në mikroqarqe. Më të përhapurit janë çipat TDA për përforcimin e sinjaleve audio. Aktualisht të përdorura në radiot e makinave, subwooferët me energji, altoparlantët e shtëpisë dhe shumë amplifikues të tjerë audio, ato duken diçka si kjo:
Të mirat e çipave TDA
- Për të montuar një përforcues mbi to, mjafton të furnizoni me energji elektrike, të lidhni altoparlantët dhe disa elementë radio.
- Dimensionet e këtyre mikroqarqeve janë mjaft të vogla, por ato do të duhet të vendosen në një radiator, përndryshe do të nxehen shumë.
- Ato shiten në çdo dyqan radio. Ka disa gjëra për Aliun që janë pak të shtrenjta nëse i blini me pakicë.
- Ato kanë të integruara mbrojtje të ndryshme dhe opsione të tjera, si heshtja e zërit, etj. Por sipas vëzhgimeve të mia, mbrojtjet nuk funksionojnë shumë mirë, kështu që mikroqarqet shpesh vdesin ose nga mbinxehja ose nga. Pra, këshillohet që të mos lidhni kunjat e mikroqarkut me njëra-tjetrën dhe të mos e nxehni shumë mikroqarkullin, duke shtrydhur të gjitha lëngjet prej tij.
- Çmimi. Nuk do të thoja se janë shumë të shtrenjta. Për sa i përket çmimit dhe funksioneve, ato nuk kanë asnjë të barabartë.
Përforcues me një kanal në TDA7396
Le të ndërtojmë një përforcues të thjeshtë me një kanal duke përdorur çipin TDA7396. Në kohën e shkrimit, e mora me një çmim prej 240 rubla. Fleta e të dhënave për çipin thoshte se ky çip mund të prodhojë deri në 45 Watts në një ngarkesë 2 Ohm. Kjo do të thotë, nëse matni rezistencën e spirales së altoparlantit dhe është rreth 2 ohms, atëherë është mjaft e mundur të merrni një fuqi maksimale prej 45 vat nga altoparlanti.
Kjo fuqi është mjaft e mjaftueshme për të rregulluar një disko në dhomë jo vetëm për veten tuaj, por edhe për fqinjët tuaj dhe në të njëjtën kohë për të marrë tingull mediokër, i cili, natyrisht, nuk mund të krahasohet me amplifikatorët hi-fi.Këtu është pika e mikroqarkut:
Ne do të mbledhim amplifikatorin tonë sipas një diagrami tipik, i cili ishte bashkangjitur në vetë fletën e të dhënave:
Ne aplikojmë +Vs në këmbën 8 dhe asgjë në këmbën 4. Prandaj, diagrami do të duket si ky:
Vs është tensioni i furnizimit. Mund të jetë nga 8 në 18 volt. "IN+" dhe "IN-" - ne dërgojmë një sinjal të dobët zëri këtu. Ne bashkojmë një altoparlant në këmbët e 5-të dhe të 7-të. Këmbën e gjashtë e vendosëm në minus.
Këtu është montimi im i montuar në mur
Unë nuk kam përdorur kondensatorë në hyrjen e energjisë prej 100nF dhe 1000uF, pasi tashmë kam një tension të pastër që vjen nga furnizimi me energji elektrike.
E tunda altoparlantin me parametrat e mëposhtëm:
Siç mund ta shihni, rezistenca e spirales është 4 ohms. Brezi i frekuencës tregon se është një lloj subwoofer.
Dhe kjo është se si duket nëndetësja ime në një banesë të bërë vetë:
Unë u përpoqa të bëj një video, por tingulli në video është shumë i dobët. Por gjithsesi mund të them që telefoni me fuqi mesatare tashmë po godiste aq fort saqë veshët e mi po rrotulloheshin, megjithëse konsumi i të gjithë qarkut në formë pune ishte vetëm rreth 10 vat (shumezohet 14.3 me 0.73). Në këtë shembull, unë mora tensionin si në një makinë, domethënë 14.4 volt, i cili është shumë brenda intervalit tonë të funksionimit nga 8 në 18 volt.
Nëse nuk keni një burim të fuqishëm energjie, atëherë mund ta montoni atë sipas këtij diagrami.
Mos u varni në këtë çip të veçantë. Këto çipa TDA, siç thashë tashmë, ka shumë lloje. Disa prej tyre amplifikojnë sinjalin stereo dhe mund të nxjerrin zë në 4 altoparlantë njëherësh, siç bëhet në radiot e makinave. Pra, mos u bëni dembel për të pastruar internetin dhe për të gjetur një TDA të përshtatshme. Pas përfundimit të montimit, lërini fqinjët tuaj të kontrollojnë amplifikatorin tuaj duke e rrotulluar çelësin e volumit deri në balalaika dhe duke e mbështetur altoparlantin e fuqishëm pas murit).
Por në artikull mblodha një përforcues duke përdorur një çip TDA2030A
Doli shumë mirë, pasi TDA2030A ka karakteristika më të mira se TDA7396
Për shumëllojshmëri, unë do të bashkëngjit edhe një diagram tjetër nga një pajtimtar, amplifikuesi TDA 1557Q i të cilit ka funksionuar siç duhet për më shumë se 10 vjet rresht:
Përforcues në Aliexpress
Kam gjetur gjithashtu komplete komplete tek Ali në TDA. Për shembull, ky amplifikues stereo është 15 vat për kanal dhe kushton 1 dollarë. Kjo fuqi është mjaft e mjaftueshme për të qëndruar në dhomën tuaj duke dëgjuar këngët tuaja të preferuara.
Mund ta blini.
Dhe këtu eshte gati menjehere
Dhe në përgjithësi, ka shumë nga këto module përforcuese në Aliexpress. Klikoni mbi kjo lidhje dhe zgjidhni çdo përforcues që ju pëlqen.
Përforcues çipi TDA 2003
Të gjithë janë të njohur me qarkun mono përforcues në mikroqarkun TDA 2003. Përdoret në pajisje të ndryshme radio: televizorë, altoparlantë kompjuteri, radio makinash, etj. Ky mikroqark amplifikator mundësohet nga një tension prej 8 - 18 volt, konsumi aktual në pjesa tjetër është -50 mA, maksimumi është 3A. Fuqia dalëse (Up=14V): - RL=4.0 Ohm - 6 W - RL=3.2 Ohm - 7.5 W - RL=2.0 Ohm - 10 W Analoge - K174UN14.
Një ULF shumë i thjeshtë në dy mikroqarqe dhe dy transistorë
Amplifikatori zhvillon fuqi dalëse deri në 25 vat për kanal. Mund të funksionojë me një ngarkesë prej 3-10 ohms. Në përgjithësi, një përforcues i mirë analog HI-FI THD jo më shumë se 0.03%
Përforcues i thjeshtë i basit
Specifikimet e amplifikatorit:
Gama nominale e frekuencës, Hz...................63...12500. Tensioni nominal i hyrjes, V................................. 0,25. Fuqia e vlerësuar e hyrjes, W, në një ngarkesë me një rezistencë prej 4 Ohms me një koeficient harmonik prej jo më shumë se 1% ......................... ......... 2.
UMZCH në TDA2005
Një UMZCH i thjeshtë në një çip të lirë TDA2005. Zhvillon fuqi deri në 18 W, funksionon mirë nga një rrjet i makinës në bord dhe nga një burim laboratori. Nuk kërkon ndonjë konfigurim - thjesht duhet ta montoni siç duhet dhe mos harroni për radiatorin. Printimi jepet "në një pasqyrë" nën një "hekur lazer". Kondensatorët për tension jo më të ulët se tensioni i furnizimit. Shpresoj të jetë e dobishme për dikë.
ULF i fuqishëm për qendrën audio
Kur krijoni vetë një qendër audio ose përmirësoni një ekzistuese, ose zhvilloni një përforcues për një kinema në shtëpi, mund t'ju duhet një modul kompakt dhe i fuqishëm UMZCH. Një përforcues i bërë në bazë të mikroqarkut TDA 7294 është shumë i përshtatshëm në këtë kuptim; avantazhe të tilla të mikroqarqeve si fuqia e lartë e daljes, një gamë e gjerë e tensionit të furnizimit dhe
niveli i ulët i shtrembërimit harmonik, i kombinuar me një çmim shumë të volitshëm, e bëjnë atë tërheqës për t'u përdorur
përforcues në shumë dizajne të pajisjeve audio të bëra në shtëpi, si dhe gjatë riparimit dhe modernizimit të pajisjeve ULF të prodhuara në mënyrë industriale.
Specifikimet:
2. Tensioni nominal i furnizimit +30V.
3. Fuqia maksimale e daljes në një tension të vlerësuar të furnizimit me një ngarkesë prej 4 Ot është 100 W.
4. Impedanca hyrëse 22 kOt.
5. Ndjeshmëria 750 mV.
6. Koeficienti i shtrembërimit harmonik me fuqi 60W, jo më shumë se 0,5%.
7. Rezistenca e ngarkesës nga 4 në 8 Ot.
Duke zgjedhur R1 ose R2 ju mund të rregulloni ndjeshmërinë e amplifikatorit të fuqisë. Përforcuesi ndizet në një "mënyrë të butë"
duke përdorur çelësin S1. Ekziston një ndërprerës S1 për të dy kanalet; nëse ka dy kanale, thjesht nuk do të ketë një kanal të dytë në qark
rezistorët R7 dhe R6, dhe pika e lidhjes së R4 dhe R5 është e lidhur me një pikë të ngjashme të kanalit tjetër.
Kunjat 5, 12 dhe 11 të mikroqarkut nuk përdoren, në mënyrë që të mos ndërlikojnë paraqitjen e tabelës; ato nuk janë të lidhura askund. Nuk ka as vrima për ta. Ata duhet të palosen ose hiqen. Një radiator është jashtëzakonisht i nevojshëm, pasi gjatë funksionimit mikroqarku nxehet shumë shpejt dhe dukshëm.
Nuk mund ta ndizni amplifikatorin pa radiator, qoftë edhe për një kohë të shkurtër. Me një fuqi prej rreth 100 W, sipërfaqja e radiatorit duhet të jetë së paku 500 cm2. Ju gjithashtu mund të përdorni një radiator me një sipërfaqe më të vogël, por siguroni rrjedhën e tij të detyruar të ajrit duke përdorur një tifoz, për shembull, nga një burim energjie
Kompjuter personal
Nuk është e nevojshme të izoloni ngrohësin nga mikroqarku, por vetëm
nëse nuk është i lidhur me telin e përbashkët të rrymës ose me pjesë të tjera të ndezura përveç autobusit të energjisë negative. Fakti është se TDA7294 ka një qark negativ të energjisë në kontakt me pllakën e radiatorit.
ULF në çipin TDA7294
TDA7294- ideja e SGS-THOMSON Microelectronics, ky mikroqark është një përforcues me frekuencë të ulët të klasës AB dhe është ndërtuar mbi transistorë me efekt në terren. Është pothuajse e pamundur ta çaktivizoni, me fjalë të tjera, ta digjni, ka mbrojtje kundër qarqeve të shkurtra dhe mbinxehjes.
Përparësitë e TDA7294 përfshijnë si më poshtë:
Fuqia dalëse 70 W për një ngarkesë me një rezistencë prej 4 Ohms, me shtrembërim prej 0,3-0,8%;
Funksionet e heshtjes dhe pritjes;
niveli i ulët i zhurmës, shtrembërimi i ulët, diapazoni i frekuencës 20-20000Hz, diapazoni i gjerë i tensionit të funksionimit - ±10 - ±40V.
Ura e fuqishme ULF 4x40 W në TDA8571J
ULF është bërë në një qark të integruar TDA8571J (DA1). Ky IC është një ULF i klasit B dhe është i instaluar në pajisjet audio të makinave për të marrë një sinjal muzikor dalës me cilësi të lartë me fuqi mesatare. Mikroqarku përmban katër amplifikatorë identikë të urës që zhvillojnë fuqi deri në 40 W në një ngarkesë 4 Ohm.
Specifikimet e amplifikatorit
- tensioni i funksionimit Upab = 14.4V (8-18V);
- rezistenca nominale Rn = 4 Ohm;
- diapazoni i frekuencës F = 20... 20000 Hz
Duke mbyllur kontaktet SW1, mikroqarku transferohet nga modaliteti i gatishmërisë në modalitetin e funksionimit dhe anasjelltas.
Një tipar karakteristik i këtij mikroqarku është prania e daljes diagnostikuese 9, e cila nga ana tjetër bëri të mundur shfaqjen e situatave të mëposhtme të urgjencës:
Mbingarkesa e IC
Mbinxehja e IC
Qark i shkurtër në ngarkesë
Vëmendje e veçantë duhet t'i kushtohet lidhjes së amplifikatorit me burimin e energjisë: IC është jashtëzakonisht i ndjeshëm ndaj tensionit të furnizimit - maksimumi 18 V. Ndryshimi i polaritetit të tensionit të furnizimit çon në dështimin e IC.
Çipi i amplifikatorit duhet të instalohet në lavamanin e nxehtësisë. Si radiator, mund të përdorni kutinë metalike ose shasinë e pajisjes në të cilën është instaluar ULF. Gjatë instalimit, rekomandohet përdorimi i pastës përçuese të nxehtësisë së llojit KTP-8.
Në vend të transistorit VT1, KT3102, KT315 dhe të ngjashme janë mjaft të përshtatshme; në vend të VT2 do të ketë KT3107, KT361; LED - çdo