Circuite practice ale amplificatoarelor cu tuburi folosind transformatoare TN
Schema 1. Amplificator cu două tuburi folosind triode-pentode 6F3P sau 6F5P.
Schema este clasică și nu necesită o descriere detaliată a fizicii funcționării sale.
O etapă diferențială este utilizată ca etapă de amplificare preliminară și reflex de bas. Curentul anodic al fiecărei triode este de 1,45 mA. În acest caz, câștigul cascadei de la intrare la fiecare ieșire este de 25. Sensibilitatea amplificatorului de la intrare, la puterea maximă de ieșire, este de 0,45 volți valoare efectivă.
Etapa de ieșire a amplificatorului funcționează cu polarizare automată în modul clasa AB. Echilibrul curent al lămpilor de ieșire este stabilit printr-o modificare mică (plus/minus 1,5 volți) a polarizării rețelei lor.
Alimentarea este realizată pe baza transformatoarelor TAN standard cu redresor semiconductor punte și filtru clasic C-L-C în formă de U. Pentru lămpile „curente” de joasă tensiune, este de preferat utilizarea diodelor semiconductoare în redresor în locul kenotronilor.
Parametrii amplificatorului pentru acest circuit sunt prezentați în primele două rânduri din Tabelul 4.
Înlocuirea 6F3P cu 6F5P nu va duce la o schimbare a circuitului, cu excepția faptului că va trebui să lipiți din nou cablajul panourilor și să porniți înfășurările transformatorului de ieșire. De asemenea, este posibil să folosiți pentode „single” 6P18P, 6P43P în acest circuit și să efectuați etapa diferențială a invertorului de fază pe o triodă dublă 6N23P. O astfel de diagramă este prezentată în figura următoare. Aici, se utilizează o serie diferită de transformatoare de alimentare, iar prestaja este setată la dublul tensiunii de alimentare a anodului pentru o mai bună liniaritate.
Schema 2. Amplificator cu trei tuburi pentru 6N23P și 6P43P sau 6P18P.
Circuitul este complet asemănător cu cel precedent, cu singura diferență că treapta diferențială preliminară este realizată pe o triodă dublă 6N23P. Curentul anodic al fiecărei triode este de 6,25 mA. Câștigul unui astfel de circuit de la intrare la fiecare dintre ieșirile parafazate este de 14. În consecință, sensibilitatea amplificatorului de la intrare, la puterea maximă de ieșire, este de 0,8 volți valoare efectivă.
Dacă doriți să furnizați un semnal de intrare în parafază amplificatoarelor conform schemelor 1 și 2, trebuie să aplicați un semnal invers rețelei celei de-a doua triode prin condensatorul disponibil în circuit (0,47 μF) prin deconectarea terminalului său inferior în circuitul de la magistrala comună. În acest caz, sensibilitatea amplificatorului pentru fiecare intrare va fi de 2 x 0,4 volți. În Schema 1, sensibilitatea amplificatorului cu un semnal de parafază va fi de 2 x 0,225 volți.
Sursa de alimentare din elementele sale constitutive este complet similară cu circuitul anterior, cu toate acestea, fizica funcționării sale este diferită. Prestajul este alimentat cu o tensiune crescută de + 370 volți de la redresorul în punte pentru a oferi o liniaritate mai mare a câștigului și o mai bună simetrie a circuitului datorită valorii mari a rezistorului din circuitul catodic comun și, în consecință, o cădere mare de tensiune pe acesta (+ 70 volți). Etapa de ieșire este alimentată de un redresor cu undă completă format din două diode punte cu anozi împămânțiți, iar un potențial de +200 volți este extras din punctul mijlociu al înfășurării anodului. Filtrul anti-aliasing este similar cu schema anterioară.
Gama de frecvență la jumătate de putere (0,707 tensiune) de la 40 Hz la 25 KHz.
Sensibilitatea amplificatorului la puterea maximă de ieșire este de 0,25 ... 0,3 volți.
Parametrii variabili ai amplificatoarelor conform schemelor 1 și 2 sunt rezumați în Tabelul 4.
Tabelul 4.
lămpi | Ieșire tr-r. | Putere tr-r. | Put [W] | Raa [Ohm] | Ea [V] | Iao | - Eg1 [V] | Rk [Ohm] | Rc [Ohm] |
6F3P | TN33, 36 | TAN2, 14, 28, 42 | 9 | 5000 | 220 | 2 x 32 | 16 | 270 | 240 |
6F5P | TN36, 39 | TAN2, 14, 28, 42 | 14 | 4050 | 220 | 2 x 40 | 20 | 120 | 270 |
6P18P | TN36, 39 | TAN4, 17, 31, 45 | 9 | 5600 | 200 | 2 x 60 | 11 | 330 | 75 |
6P43P | TN36, 39 | TAN4, 17, 31, 45 | 15 | 3333 | 200 | 2 x 60 | 16 | 330 | 130 |
Schema 3. Push-pull ULF pe lămpile „televizor”.
Preamplificatorul din acest circuit este format din două trepte. Modul primei etape de amplificare pe partea triodă a 6F1P a fost ales aproape de cel standard cu un curent anodic de 10 mA și o tensiune anodică de 93 volți. Câștig de etapă 7.
Invertorul de fază este realizat conform circuitului unui amplificator diferenţial de parafaza bazat pe o triodă dublă 6N23P cu o sursă de curent într-un circuit catod comun. Partea pentodă a lămpii 6F1P a fost folosită ca sursă de curent. Schema de cascadă diferențială este complet similară cu cea anterioară. Curentul anodic al fiecărei triode este de 6,25 mA. Câștigul este 14. Astfel, factorul total de pre-câștig va fi 98.
Sensibilitatea UMZCH conform schemei 3 la puterea maximă de ieșire va fi de 0,23 volți valoarea efectivă.
Deoarece tensiunile de alimentare anodice ale amplificatoarelor cu VT sunt fixate rigid și determinate de calculele de mai sus, iar parametrii lămpilor „cadru” și „linie” sunt în mare măsură consecvenți, pare posibil să se dezvolte un singur circuit amplificator pentru 6P36S, 6P41S, 6P42S, 6P44S, 6P45S. Doar parametrii unor elemente pasive, includerea înfășurărilor secundare și evaluările de tip ale transformatoarelor de putere și de ieșire vor fi diferiți. Ei bine, desigur, curenții consumați de la sursa de alimentare și puterile de ieșire ale amplificatoarelor vor fi, de asemenea, semnificativ diferite.
Ca redresor de alimentare cu anod pentru un amplificator care utilizează tuburi de curent, este mai bine să utilizați o punte semiconductoare, după care este instalat un filtru de netezire C-L-C. Acest circuit, în comparație cu un redresor kenotron, va oferi o mai bună stabilitate a tensiunii joase a anodului la curenți de sarcină mari. Și curenții anodici din aceste amplificatoare vor fi foarte semnificativi. Un rezistor de 1 kilo-ohm în borna negativă a podului anodic limitează curentul de încărcare al condensatorilor filtrului și trebuie scurtcircuitat după pornirea amplificatorului, dar nu mai devreme de 5 secunde.
Parametrii variabili ai amplificatoarelor conform schemei 3 sunt rezumați în Tabelul 5
Tabelul 5.
lămpi | Transformator de ieșire | Transformator de putere | Put. [W] | Raa [Ohm] | Ea [V] | Iao | - Eg1 [V] | Rg [Kohm] | Sf [µF] |
6P41S | TN42, 44, 46, 47 | TAN31, 45 | 28 | 1620 | 200 | 2 x 70 | 27 | 27 | 330 |
6P36S | TN49, 50, 52 | TAN45, 59 | 32 | 1400 | 200 | 2 x 60 | 24 | 20 | 470 |
6P44S | TN54, 56, 57 | TAN73 | 43 | 1040 | 200 | 2 x 100 | 33 | 43 | 470 |
6P42S | TN58, 59 | TAN73, 108 | 49 | 920 | 200 | 2 x 100 | 33 | 43 | 680 |
6P45S | TN60, 61 | TAN108 | 56 | 800 | 200 | 2 x 150 | 37 | 68 | 680 |
O versiune de amplificator care utilizează tuburi 6P44S este prezentată în diagrama de mai jos. Echilibrul circuitului etapei de ieșire este reglat în limite mici folosind un potențiometru în grilele ecranului. După setarea anterior a acelorași curenți ai lămpii în modul de repaus cu acest rezistor, reglarea finală a simetriei circuitului trebuie efectuată la un semnal nominal cu un minim de distorsiuni neliniare.
La instalarea amplificatoarelor, este necesar să rețineți că transformatoarele blindate TAN31, 45, 59 și transformatoarele cu tijă TAN73, 108 au numere de pin diferite.
De asemenea, puteți încerca conexiunea triodă pentru lămpile curente prin conectarea rețelei ecranului la anod; din fericire, modul lor tipic oferă aceleași tensiuni de alimentare pentru anod și rețeaua ecranului.
De asemenea, puteți comuta treapta de ieșire în modul clasa A cu polarizare automată - cu un rezistor comun în catozii de 140 ohmi pentru 6P44S (6,6 W vor fi disipați de acest rezistor, deci trebuie să conectați patru rezistențe de 2 wați de 560). Ohmi în paralel), desigur, ajustând alimentarea anodului la acești 30 de volți, conectând în serie cu înfășurările anodului înfășurările de polarizare liberă 11-12 și 20-21. Astfel, cu auto-polarizare, tensiunea de alimentare a anodului va crește la aproximativ 230 de volți. Cu toate acestea, va trebui să verificați tensiunea de alimentare înainte de a vă asigura că nu depășește limita de 450 de volți pentru condensatoarele electrolitice. Tensiunea în exces va fi absorbită de un rezistor de 10 kiloohm de 1 watt conectat direct la borna pozitivă a podului anodic înainte de a o conecta la condensatorul filtrului. O conexiune similară a unui rezistor de stingere este prezentată în diagrama 2.
Același circuit amplificator va oferi câștigul și intervalul necesar al tensiunii de ieșire a invertorului de fază pentru acționarea lămpilor „reglatoare” de tipurile 6S19P, 6S41S, 6S33S. Dar acesta este subiectul unuia dintre articolele următoare.
Transformatoarele TN deschid posibilități enorme de proiectare a circuitelor în proiectarea amplificatoarelor cu tub push-pull, chiar și până la reproducerea sunetului de înaltă calitate.
Experiment!
Bună prieteni! Vreau să vă spun despre crearea propriului meu tub ULF pe 6P36S. Acesta este un push-pull cu un offset fix conform schemei lui S. Sergeev.
Era în vacanța de vară, era mult timp, era cunoștințe, era dorință. Așa că am decis să fac un fel de amplificator stereo cu tuburi pentru a asculta muzică. Da, da, a fost cel de tub, nu mi-au plăcut niciodată „pietrele”.
Am început să mă gândesc ce circuit să iau, cu ce lămpi? Am decis să aleg ceva dintre lămpile pe care le aveam. Din anumite motive, nu am vrut să folosesc lămpi 6P15P și 6P43P. Mă gândeam la opțiunea 6P13S, dar am citit o recenzie negativă. Până la urmă m-am așezat pe 6P36S. Mi-a plăcut și aspectul ei: atât de mare și de impresionant. Iar recenziile despre el sunt pozitive.
Circuit amplificator cu tuburi de S. Sergeev
Puterea mare și prezența tuburilor potrivite în faza de șofer m-au convins să construiesc primul meu push-pull.Amplificatorul sună foarte bine și are următorii parametri:
Tensiune de alimentare 360 volți
Consumul de energie din rețea 170 W
Sensibilitate 0,7 volți
Putere de iesire 40 W
Înarmat cu o listă de piese, am mers la piață. Din păcate, acesta este singurul loc de unde poți cumpăra piese radio din orașul meu.
Transformator de putere TSA-270
Ca transformator de alimentare, am vrut să folosesc un transformator standard derulat, de exemplu TS-180. Mi s-a gasit doar TCA-270 pe care l-am cumparat si am plecat acasa destul de multumit. Deși înfășurarea este din aluminiu (indice A), oferă parametrii pașaportului.Am conectat TCA-270 astfel:
Concluzii 7-17 folosit pentru a obține tensiunea de polarizare a unui canal
Concluzii 4-14 pentru alimentarea cu anod a unui canal
Concluziile 11-(21-12)-22 pentru filament 6P36S de un canal. Terminale 20-(10-10’)-20’ la incandescența 6N1P a ambelor canale.
Înfășurările pe care le-am dat asigură exact tensiunea și curentul necesar.
Transformator de ieșire TS-180
Am folosit un TS-180 ca transformator de ieșire și l-am conectat conform circuitului propus de Manakov.Placa de montare la suprafata
Aș dori să vă atrag atenția asupra modului meu nestandard de a crea table. Cert este că nu gravesc sigila, am tăiat folia de pe PCB în pătrate de 2 cm x 1 cm și am venit cu o diagramă pentru cablarea pieselor. De exemplu:
Schema conform căreia am lipit piesele pe placă.
Liniile dintre pătrate sunt săritori. Există și conexiuni mai lungi, sunt desenate ca linii. Săgețile de pe pătrate indică locul în care vor fi lipite firele de la panourile lămpii, sau puterea etc. De exemplu, 3L1 înseamnă că al 3-lea pin al primei lămpi (6N1P) este lipit acolo, 8L2 înseamnă că al 8-lea pin al celei de-a doua lămpi (6P36S) este lipit acolo. Acestea. prima cifră este numărul PIN, litera este pur și simplu împărțită, iar a doua cifră este numărul lămpii.
Nu vă sugerez să faceți același lucru, doar că această metodă este simplă și economisește timp și bani. Se dovedește a fi un „baldachin” pe PCB.
Iată placa pe care am primit-o
Primul start
Prima lansare a avut succes. Există o singură păcat: la vremea aceea nu aveam multimetru la îndemână. Cea veche e stricata, nu am cumparat inca una noua. În general, l-am configurat folosind o metodă barbară: am ajustat offset-ul astfel încât să fie minim, dar anozii nu au devenit roșii.Totul pare să funcționeze, este timpul să-l ascundeți în carcasă. Și apoi am fost foarte norocos: o cunoștință a tatălui meu mi-a dat o chitară ULF „Minor” veche, care nu funcționează, care a fost imediat eviscerată.
Carcasa de la „Minor” se potrivește perfect, două transformatoare de ieșire TS180 (întinse) și 2 plăci ale ULF-ului însuși se potriveau în ea, dar transformatorul de putere TCA-270 nu se potrivea. Prin urmare, a fost realizată o carcasă separată pentru alimentarea cu energie din PAL și placaj. Partea superioară a corpului este acoperită cu bandă autoadezivă.
Au fost forate găuri pentru panouri. Totul este instalat, iar acum lansarea mult așteptată în carcasă. Îl aprind și... aproape că am surd de la fluier când lămpile s-au încălzit! Blestemat, opresc curentul și merg la piață să cumpăr un fir ecranat, cumpărându-l cu rezervă.
Combaterea excitării - scut
Pentru a elimina autoexcitarea, care se manifestă ca un fluier, a fost necesar să se protejeze circuitele de rețea ale triodei 6N1P și firele din circuitele rețelei a două 6P36S. Anozii 6P36S nu au fost ecranați. Fluieratul s-a oprit.Îl pornesc din nou și aud: un canal funcționează grozav, dar în celălalt există clicuri în loc de bas, plus un mediu lent și răgușit. Bineînțeles că am fost supărat în acest moment. Si ce nu am incercat? motivul s-a dovedit a fi screening-ul incorect al plasei. Ecranele nu au fost împământate corect.
Am refăcut-o, am împământat capetele ecranelor cu o stea - atunci toate firele merg la un punct și la corp. Interferența și entuziasmul au dispărut, clicurile din bas s-au oprit, basul a devenit clar, elastic și ambele canale au început să cânte la fel de frumos.
Detalii
În amplificator am folosit rezistențe MLT și OMLT cu o putere de 1-2 Watt. Am cumpărat toate rezistențele cu o putere de 1-2 wați. Condensatoarele C3 și C4 sunt de tip K73-17, iar C2 a fost furnizat de BMT-2. Am in driver un bec 6N1P, care poate fi inlocuit cu un 6N23P fara nicio modificare a circuitului. Dar îmi place mai mult sunetul lui 6N1P.Tuburile de ieșire 6P36S, pentru a crește puterea amplificatorului, pot fi înlocuite cu 6P42S, setând un curent de repaus mai mare, undeva în jurul valorii de 106 mA (scădere peste rezistențele catodice 1,06 V)
Setarea și caracteristica offset fixe
După achiziționarea multimetrului, configurarea a devenit ușoară, dispozitivul este în stare de funcționare și la îndemână: rezistența R9 a stabilit aceeași tensiune pe catozii lămpilor, iar rezistența de polarizare a stabilit tensiunea la 0,55 volți.Cu toate acestea, există o caracteristică neplăcută a unui offset fix. Când tensiunea rețelei se modifică, modul lămpii se schimbă. Odată ce tensiunea din rețea a crescut la 250 V și un 6P36S a ieșit din funcțiune, anodul a devenit fierbinte, curentul de repaus a crescut la 80 mA (cu 55 mA prescris)! Din fericire, am observat imediat acest lucru și am oprit ULF-ul.
A trebuit să instalez un stabilizator de tensiune „Ucraina-3”, al meu produce 215 V. Din cauza tensiunii insuficiente pe primar (și, în consecință, pe secundar), tensiunile de pe anozi au scăzut de la 330 V necesar la 313 V. Am crescut curentul de repaus la 64 mA (cădere între rezistențele R12, R13 = 0,64 V).
6P45S este o lampă foarte potrivită pentru consumatori! Pentru o bandura atat de sanatoasa se face foarte prost! În primul rând, există o gamă largă de parametri. În al doilea rând, catodul și terminalul sunt foarte prost conectate, blocate cu un fir minuscul care se arde la orice supratensiune. Am dat peste cap vreo 5 lămpi, doar catodul a două dintre ele nu s-a ars imediat, s-a ars...într-o zi! Și doar unul a funcționat timp de o lună.Pentru a evita dezlipirea, am vrut să pun în paralel două dintre ele, dar curentul de filament de 5 A mi s-a părut prea mare. Le-am folosit în convertorul meu de înaltă tensiune cu tub:
http://stalin.flyback.org.ru/tubeflyback.htm
Apoi am instalat un 36 în loc de 45, totul funcționează de aproximativ o lună, 36 de fapt ține calm 600(!) volți și 30 wați la anod. Fiabil ca o piatră (în sensul bun).
Arkadi Antonov
> puterea anodului 6p36s-20 wați
Poate fi așa, dar lampa are calm 27 - 28 de wați la anod... Da, și treizeci nu o vor speria
Din experiența mea, 36 sună mai convingător (față de 45)
Pronin
Cele mai bune tetrode de cadru, după părerea noastră, sunt lămpile 6P42S FĂRĂ ANOD DE CAMERA. Ele sunt, totuși, extrem de rare, iar sensul producției lor în Svetlana în 1972-1975 este în general neclar. Cu toate acestea, ele există, le puteți găsi. De asemenea, foarte bune sunt 6P36S și 6P42s cu un anod alb „pufos”. De asemenea, sunt absolut „indestructibili”, aparent datorită stratului de acoperire al anodului.
Caracteristicile de sunet ale acestor lămpi depind în mare măsură de modurile utilizate.
Prin urmare, este dificil să vorbim despre sunet în afara acestor legături de „mod”.
> Și oricum, care sunt limitele pentru 36 și 42?
Îmi place modul 300 V, 125 mA pentru 6P42S și 300 V, 72 mA pentru 6P36S.
Sarcina este absolut corectă - 2 și, respectiv, 4 com.
Puteți să-l înfășurați pe 2 comunicatoare, să puneți două prize și să ascultați fie unul 6P42S, fie două 6P36S în paralel.
Nu este nevoie să setați 5Ts3S, sunetul va fi muzical, dar lent. Instalați două 6D22S și obțineți muzicalitate selectând părți.
Și, în orice caz, nu are rost să încărcăm kenotronul în spațiu.
Shalin
Ei bine, poate cineva să-mi spună modurile optime pentru acest tub într-o triodă și rezistența internă și Mu la punctul de funcționare... Am tot căutat - am ascultat amplificatorul de pe aceste tuburi și se joacă mai bine cu același design de circuit decât EL34 și mult mai bun decât EL84. Spre deosebire de 6P45S, ele mențin stabil modul fără a pluti în termocurenți la o deplasare fixă. Ei bine, în general, fă tot ce poți pentru a ajuta. Din câte înțeleg, nu există grafice anodice pentru această lampă în natură - nici măcar nu am „minister” în cartea mea de referință.
Gajdar
Atunci este mai bine să utilizați 6P36S. Ea joacă ȘI MAI MAI BUN decât 6P44S
Shalin
> Salut Alexey. Din moment ce esti pe forum, spune-mi modul pentru SE 6P36S si
> sarcina dată sau câteva opțiuni. Mulțumesc Eduard.
Pentru 6P36S: 330 V, 70 mA, Ra = 5 com.
Îmi place acest mod
Shalin
> Doar 6P36S este similar cu 6P42S din primele versiuni.
> Și 6P36S au mai puțină răspândire și sunt mai stabile.
Și astăzi am fost convins de asta - doar selectam perechi din 6p36s:
Am reușit să alegem dintre 15 bucăți
1 pereche perfectă
1 cvartet imperfect
4 lămpi accelerate
Ei bine, 5 piese sunt complet diferite.
Randamentul de 40% este un rezultat bun
Și acest cuplu ideal sună foarte frumos.
Barbă
Există Svetlanov și Ulyanovsk 6P36S cu anozi gri deschis - joacă mai bine decât cei gri.
Shalin
Mai bine cu „42”. Anodul 42 este puțin mai mare decât al 36-lea și similar cu acesta, iar al 45-lea este
De 1,5 ori mai sus și la capete pe ambele părți sunt trei orificii dreptunghiulare de aproximativ 6x6 mm. Se pare că A. Shalin a postat undeva fotografii cu cele 42 corecte. Al 36-lea deci - dacă anodul este aproape alb și „pufos” sau gri deschis și din nou „pufos” - atunci trebuie să îl salvați, chiar și unul folosit.
HRYUN
Trebuie să-l porniți timp de 2-3 minute, doar suficient pentru ca lampa să se încălzească. Se simt normali. Aceasta nu este încă o supraîncălzire gravă. Patruzeci și cinci este o doamnă puternică. Le adună doar prost.
Sensul unui astfel de control este următorul. Într-o tetrodă cu fascicul, ambele grile au aceeași pasă și trebuie instalate astfel încât firele grilei să fie exact una față de alta. Așa se formează razele. 6P45S și 6P36S au aproape același design catodic-grilă - 4 cadre cu fire sudate. Două cadre pe o parte a catodului, două pe cealaltă. Rezultă două seturi de raze în direcții diferite de la catod, la jumătățile opuse ale anodului. Să presupunem că pe o parte ramele nu sunt aliniate exact. Apoi, curentul fasciculului pe această parte va fi mai mic decât pe cealaltă parte, iar jumătatea anodului de pe această parte se va încălzi mai puțin decât pe cealaltă parte. Jumătate din lampă este o tetrodă cu fascicul, iar jumătate este una convențională. Și aceste două tetrode, cu caracteristici diferite, sunt conectate în paralel. În principiu, puteți folosi un pirometru pentru a măsura temperatura diferitelor părți ale anodului, dar în absența unuia, încălziți lampa pentru o perioadă scurtă de timp până când apare roșeața. Dacă devine roșu mai mult pe o parte, este un semn clar al unui defect de fabricație. Va funcționa bine în scanarea orizontală, dar este mai bine să nu îl utilizați în sunet. Există aproximativ 80-90% dintre astfel de lămpi defecte.
Oleg
Mesaj de la KHRUN
Și adevărul este HORROR...! Îți voi spune secretul meu teribil: cumva (cu mult timp în urmă)
6P36S al meu (de epocă) a funcționat destul de mult timp în modul 250 V,
160 mA (40 wați, totuși...) cu auto-bias (mai exact, aproape cu auto-fix, dar atunci nimeni nu știa că este auto-fix). Și nimic, au rămas în viață.... Gridlik era, se pare, 51 kOhm.
De asemenea. Doar Svetlanov 6P36S folosit de mine a funcționat câteva luni în modul 100 mA 400V și cu o remediere.
Dalka
Și tocmai acesta este motivul sunetului prost... Am dat peste 45s care s-au făcut roșii pe o parte la 40 de wați la anod, poate puțin mai mult. Au lăsat imediat gunoiul. Câtă putere poate disipa lampa selectată înainte de a deveni roșu?
Serghei Z
Cei selectați la 60 practic nu se înroșesc. Doar în întuneric complet se observă o ușoară strălucire. Într-adevăr, aceasta este o alternativă bună la 6S33S. Este mult mai ușor de balansat și mult mai liniar.
Oleg
M-am uitat la curbele triode I-V ale 45-a.
Am gasit un mod:
250V, 180mA, -50V pe rețea.
Ri = 290 ohmi, Ra = 2380 ohmi, alfa = 8,2.
Uam = 181 v, Iam = 76 mA,
P~ = 6,88 W.
Liniaritatea în acest mod este foarte mare.
În modul 250 V, 240 mA, nu va fi posibilă o sarcină mai mare de 1242 ohmi, deoarece atunci jumătatea dreaptă a liniei de sarcină va depăși chiar curba de putere de 60 (!!!) wați.
Într-un cuvânt, orice s-ar spune, utilizarea lui 6P45S cu o putere a anodului de peste 45 W este îndoielnică pentru mine...
Shalin
6P36S sunt lămpi foarte rezistente la vibrații cu grile de cadru puternice, au un microfon mic.
Shalin
IMHO, în comparație cu 6P36s, 6P44S este mai întâi captivat de noutatea sunetului, apoi, după ascultare,
înțelegi că sunetul este „înțepător și aspru”, dar subiectiv sunt mai multe înalte,
atunci când se măsoară o coadă mai lungă de armonici, s-au efectuat doar măsurători comparative
o etapă de ieșire pe lămpi diferite, toate celelalte lucruri fiind egale.
În ceea ce privește răspândirea, Svetlanov 6P44S are parametri mai apropiați decât 6P36S,
pentru 6P44S spread-ul mediu este de până la 30-35%, 6P36S până la 50%.
Totul se învață prin comparație, dar anterior nefolosit, selectat 6P31S, IMHO au cel mai mult
sunet natural, apropiat de sunetul lui 2A3 în medii și înalte.
Manakov
Dmitry, unul dintre amplificatoarele mele 6P36S funcționează de 8 ani la 20 de wați pe anozi fără a înlocui lămpile. Prietenul meu are trei ani la 27 de volți.
Undeva, Hryun a subliniat că în modul forțat (36 de wați la anod), Ri-ul lui 6P36S scade la 450 ohmi.
Eu însumi încerc să nu „chinuiesc” 6P36S cu mai mult de 28 de wați.
Shalin
Dmitry, asta înseamnă că lămpile nu erau foarte bune
6P36S bun se comportă perfect cu 33-100 ohmi în grilă. Dar măsuri anti-excitare sunt cu siguranță necesare, este adevărat.
Nu am testat 6P36S cu o putere de anod de peste 32-33 de wați, dar prietenul meu din amplificator cu un 6P36S (construcția mea) l-a conservat la 37 de wați și trăiește normal cu un fixativ și chiar fără un cioț de anod.
Shalin
Printre creatorii de amplificatoare cu tuburi, tuburile care au fost folosite anterior în televizoare sunt pe măsură de populare. 6N23P, 6F3P, 6P45S sunt încă foarte populare printre producătorii de amplificatoare și aceasta nu este o listă completă a unor astfel de lămpi. Printre aceste lămpi există lideri în popularitate, deoarece lămpile de ieșire, de exemplu, cele mai populare sunt 6P36S și 6P42S, iar această popularitate este binemeritată. Când este bine interpretat, sunetul amplificatoarelor de pe aceste tuburi mulțumește urechile cu discernământ ale multor iubitori de muzică.
Mai jos este una dintre versiunile unui amplificator cu un singur capăt cu un tub de ieșire 6P42S.
Pentru a porni complet 6P42S, aveți nevoie de un semnal cu o amplitudine de 70-80 Volți. Este destul de problematic să obțineți o astfel de amplitudine folosind un driver cu o singură etapă de la o sursă de semnal standard. Prin urmare, s-a decis să se facă șoferul în două trepte, în prima etapă E80CC a funcționat foarte bine, în a doua etapă ne-am stabilit pe EL84 în conexiune triodă, deși 6P15P și EL803 au funcționat foarte bine.
Etapa de ieșire folosește un transformator cu înfășurare catodică, care crește liniaritatea etajului și îi reduce rezistența de ieșire. Circuitul amplificatorului este prezentat în Fig. 1.
Fig. 1 Schema schematică a amplificatorului electric
După cum se poate vedea din diagramă, 6P42S este utilizat cu o polarizare fixă. Ca senzor de curent anodic, folosesc de obicei rezistența activă a înfășurării catodului, de obicei este de aproximativ 10 ohmi.
Amplificatorul este pornit în trei etape: când comutatorul general 1 este pornit, toate filamentele sunt preîncălzite, după care contactele releului 2 închid o rezistență de limitare de 1 kOhm și lămpile sunt complet încălzite și în anod furnizează tensiunea. se ridică la aproximativ jumătate. După închiderea contactelor releului 3, se aplică tensiunea anodului complet și amplificatorul este gata de funcționare.
Transformatorul de ieșire are o rezistență redusă (pentru înfășurările anodului și catodic împreună) de aproximativ 2,5 kOhm, înfășurarea catodului este de aproximativ 10% din înfășurarea anodului.
Acum despre tuburile de ieșire. Există cel puțin patru modele diferite ale acestor tuburi, cele două cele mai vechi fiind cele mai „sunătoare”, cu găuri rotunde în anod. Cel mai bun are un anod gri-argintiu, al doilea în clasament are un anod gri-șoarece. Diferența de sunet este foarte mică în favoarea celui argintiu. Cea mai recentă versiune este similară ca design cu 6P45S și sună în consecință.
Amplificatorul original folosea rezistențe BC (cu excepția anodului EL84, există cele Matsushita de cinci wați, unul la unul la fel ca Kiwame, dar albastru), condensatoare electrolitice Tesla, condensatoare interstage - K40-U9, controlul volumului - fir PPZ- 40. Dar aceasta nu este dogmă.
În concluzie despre caracteristicile măsurate: puterea maximă de ieșire a fost de 11 W cu un interval de frecvență de 8 Hz...50.000 Hz (cu o planeitate de ±3 dB) și 16...35.000 (cu o planeitate de ±0,5 dB) , Kni = 1% (cu 8 W), Rout = 1,5 Ohm.
Designul amplificatorului este prezentat în Fig. 2. În fotografie nu există o rețea de protecție, care este instalată din motive de siguranță deoarece tensiunea care pune viața în pericol este prezentă și ușor accesibilă pe capacele anodului 6P42S.
Punțile de diode din redresoarele de alimentare sunt aceleași. Într-o anumită măsură, acest lucru se datorează utilizării condensatoarelor de stocare de mare capacitate în ele.În redresor, puteți utiliza o punte de diode VD3 cu o valoare limită de curent mai mică (de exemplu, seria
KTs402), dar în acest caz un rezistor de limitare a curentului cu o rezistență de 80... 100 Ohmi ar trebui conectat în serie cu înfășurarea (5-15).
Ventilatorul (este amplasat pe panoul din spate al carcasei - vezi aspectul unităților și panourilor în Fig. 3) pentru ventilație forțată (evacuare) - aproape oricare dintr-o sursă de alimentare cu comutare, dar dacă este posibil este mai bine să alegeți unul cu un nivel mai scăzut de zgomot acustic.
Sursa de alimentare folosește șocuri folosite la televizoarele cu tub vechi, dar puteți folosi altele care sunt potrivite pentru parametri. Inductanța bobinelor L1, L2 este de 0,4 H și L3 este de 5 H.
În amplificator pot fi utilizate diferite tipuri de piese: rezistențe - MLT, MON, BC de putere adecvată cu o toleranță de cel mult 10%; Condensatoare nepolare - polietilen tereftalat cu peliculă K73-9, K73-16 sau K73-17 pentru o tensiune de cel puțin 400 V. De asemenea, este permisă instalarea condensatoarelor de hârtie din echipamente vechi - KBG-I, BMT-2, K40U- 9, MBM. Condensatoarele de oxid din sursa de alimentare și amplificator sunt importate din Jamicon sau din seria domestică K50-35, K50-26, K50-27.
Indicatorii de nivel de semnal din fiecare dintre canale (PA1) sunt săgeți (M42305 sau similar pentru 50-200 µA). Practic, îndeplinesc o funcție auxiliară și aduc din punct de vedere estetic o oarecare dinamică funcționării dispozitivului. Iluminarea indicatoarelor poate fi organizată folosind LED-uri sau lămpi incandescente miniaturale alimentate de o sursă de tensiune de 12 V în sursa de alimentare.
Amplificatorul are un design unic. În partea de jos există o sursă de alimentare montată pe propriul șasiu; în partea de sus se află blocul amplificator (două canale), tot pe un șasiu separat (vezi Fig. 3).
Amplificatorul folosește un control de volum cu un motor electric stereo ALPS RK27 100 kOhm (Blue Velvet); acest lucru vă permite să conectați o telecomandă cu fir, care are un comutator cu doi poli (comutator basculant) cu trei poziții fixe (SA1 în diagrama din Fig. 2). O altă opțiune posibilă este un joystick, care, în funcție de direcția de deviere, conectează motorul electric de antrenare la o sursă de tensiune de 12 V folosind grupuri de contacte bipolare în polaritatea corespunzătoare (puteți folosi și relee electromagnetice adecvate, de exemplu, RES22 sau similar) * Cu toate acestea, telecomanda nu neapărat - acesta este într-o anumită măsură un tribut adus modei
O atenție deosebită trebuie acordată fabricării carcasei.Deoarece amplificatorul funcționează în condiții dificile de temperatură, lemnul trebuie mai întâi bine uscat.În acest caz, plăcile au fost uscate în mod natural în condiții de cameră timp de 6 luni. După terminarea plăcilor, din ele s-a făcut un corp (foto în Fig. 4). Semnele au fost tăiate la capete la un unghi de 45° și lipite împreună cu lipici „Joiner-moment” După aceasta, corpul a fost instalat lângă radiatorul de încălzire centrală și acoperit cu o pătură. În această stare, a fost lăsat să se usuce încă două luni, după care au fost tăiate găurile și ferestrele necesare și au fost lipite elemente decorative ale panourilor din față, de sus și din spate. După aceste operații, organismul timp de o lună
M-am uscat din nou lângă calorifer, acoperită cu o pătură. Apoi a fost șlefuit și vopsit cu compoziția de nuanță Belinka-TOPLAZUR în culoarea mahon (Nr. 28) în patru straturi. Toate acestea au fost făcute astfel încât să nu existe surprize în viitor la operarea amplificatorului.
Amplificatorul are un regim de temperatură destul de intens în partea superioară a carcasei, în timp ce compartimentul inferior se încălzește cu greu. Materialul corpului insuficient uscat (în acest caz, pinul) poate izbucni de-a lungul bobului. A trebuit să muncesc din greu pentru a obține un rezultat bun: de trei ani încoace nu există plângeri cu privire la caz. Dacă nu doriți să faceți bare, corpul poate fi realizat din placaj de 15...20 mm grosime, acoperit cu furnir.
Panourile laterale ale carcasei sunt tăiate din sticlă colorată „Turquoise” cu o grosime de 5-6 mm. Când amplificatorul funcționează, ele pot fi mutate ușor înapoi, așa cum se arată în fotografia din Fig. 5; în timpul ventilației
carena se va îmbunătăți semnificativ. Pentru a ușura viața amplificatorului, pe panoul din spate este instalat un cooler pentru computer, care funcționează în două moduri - la 8 și 12 V. Poate fi pornit sau oprit dacă se dorește
Panourile din spate și din față sunt tăiate din aluminiu de 2...3 mm, șlefuite și acoperite cu lac auto acrilic transparent din ambalaj cu aerosoli.
În jurul panourilor lămpii sunt găurite găuri cu un diametru de 5...6 mm pentru a asigura o convecție naturală a aerului. Panoul superior al carcasei are o grilă metalică de protecție, care se potrivește liber în cadrul decorativ de pe acest panou
În acest model de amplificator, transformatoarele de ieșire nu sunt destul de convenționale. Ele sunt realizate pe baza unui transformator de rețea TS-90 cu un miez magnetic ShL. Toate înfășurările sunt îndepărtate din bobinele standard, iar altele noi sunt înfășurate în vrac cu un mănunchi de nouă fire PELSHO. Dintre acestea, șapte PELSHO-0.33 firele sunt utilizate în înfășurarea primară, iar două fire PELSHO-0,8 - în secundar. Schema de conectare a acestor fire în înfășurări este prezentată în Fig. 6.
Un mănunchi din aceste nouă fire, de aproximativ 10 m lungime, este înfășurat pe cadrul fiecărei bobine până la umplere (se obțin aproximativ 70 de spire) Apoi, aceste bobine se fierb în parafină timp de 15...20 de minute într-o apă. baie C
Opțiunile de transformator de ieșire sunt, de asemenea, posibile. Lămpile 6P36S au o rezistență internă destul de scăzută, iar pentru un amplificator push-pull care utilizează astfel de lămpi, de la 700 la 1000 de spire ale înfășurării primare (pentru circuitul magnetic utilizat) cu o atingere din mijloc este suficient.
Amplificatorul și sursa de alimentare sunt echipate cu plăci de circuite din fibră de sticlă acoperită cu folie. Datorita faptului ca au un model foarte simplu, acesta se taie cu un cutter din lama de ferastrau. O vedere a instalării pieselor și ansamblurilor mici în șasiul blocurilor este prezentată în foto fig. 7.
Pe panoul din spate al carcasei există terminale de ieșire pentru ambele canale, conectori de intrare, un conector de telecomandă, un conector de rețea, un comutator de ventilator (cheie roșie), un comutator de mod ventilator - un comutator basculant (tensiune 8 sau 12 V) , o bornă de masă a carcasei și un bloc de siguranțe (unul în circuitul rețelei primare și două în circuitele de alimentare cu anod ale fiecărui canal)
De la redactor. În cazul în care ventilatorul este situat sub lămpi puternice, ventilația forțată ar trebui organizată ca ventilație de alimentare.
Comentarii la articol: